EUVIMEDEUVIMED entdecken
Randomisierte kontrollierte StudieVergleichsstudieOpen Access · CC BY 4.0

Acceptability and safety of 3D printed wrist-based orthoses compared to fiberglass casts for the treatment of non-surgical distal radius- and scaphoid fractures: A randomized feasibility trial

Bernadette Tobler-Ammann, Frédéric Schuind, Loïc Voillat, Esther Vögelin

Journal of Hand Therapy · 2025

DOI: 10.1016/j.jht.2024.11.004 ↗

Kurz gefasst

Randomisierte kontrollierte Studie in der Zeitschrift Journal of Hand Therapy, 2025. Verfasst von Bernadette Tobler-Ammann und 3 weiteren Autor:innen. Beteiligte Einrichtung: Department of Plastic and Hand Surgery, Inselspital Bern, University of Bern, Bern, Switzerland. Electronic address: bernadette.tobler@insel.ch. Hauptthemen laut MEDLINE: Radius Fractures, Scaphoid Bone, Printing, Three-Dimensional, Casts, Surgical. Die Arbeit wurde bisher 12-mal zitiert (Crossref) und nennt 20 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Innosuisse Swiss Innovation Agency.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

BACKGROUND: Non-invasiveness and comfort are crucial in the conservative management of distal radius and scaphoid fractures. While fiberglass casts are standard, three-dimensional (3D)-printed orthoses offer a promising alternative. PURPOSE: To compare patient experiences, safety perceptions, and satisfaction between a 3D orthosis and fiberglass cast for distal radius or scaphoid fractures. STUDY DESIGN: Randomized feasibility trial. METHODS: Nineteen adult patients were randomly assigned (3D orthosis group, n = 10; fiberglass cast group, n = 9) and followed until orthosis or cast removal at 6-8 weeks. X-rays at weeks 1 and 6 documented bone healing, with weekly hand therapy visits assessed orthosis satisfaction and function. The Patient-Rated orthosis Satisfaction Questionnaire (PRSEQ) measured satisfaction at weeks 2, 4, and removal. Descriptive statistics and non-parametric correlation tests were used for data analysis. RESULTS: The 3D orthosis group achieved significantly higher PRSEQ scores (mean difference [MD]= 15.7%, p = 0.005 to 0.01, r = -.581 to -.638) and lower perceived pain (MD=-1.0 to -2.2, p = 0.001 to 0.048, r = -0.45 to -0.75) compared to the cast group. By week 4, the 3D group reported less discomfort (MD=-2.2, p = 0.03, r = -0.5) and felt safer (MD=1.6, p = 0.043, r = -0.46). Routine activities were easier for the 3D group at weeks 2 and 6 (MD=-2.8 to -3.0, p = 0.033 to 0.034, r = -0.49). Satisfaction scores were higher in the 3D group (mean 8.4 vs. 5.6 points, p < 0.001 to 0.01, r = -0.57 to -0.82). Compliance was excellent in both groups. No significant differences were observed in radiological outcomes, finger sensibility, or edema. Bone healing occurred in both groups without fracture displacement; however, one cast patient required subsequent surgery for scaphoid non-union. CONCLUSIONS: Treatment with a 3D-printed orthosis appeared feasible and safe, with patients reporting higher satisfaction and better self-perceived hand function compared to a custom-made fiberglass cast, although further research is needed to confirm these findings.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Radius FracturesScaphoid BonePrinting, Three-DimensionalCasts, SurgicalOrthotic DevicesFractures, BoneHumansFemaleMaleFeasibility StudiesAdultPatient SatisfactionMiddle AgedGlass

Stichwörter der Autor:innen

3D-splintingConservative treatmentDistal radius fractureFiberglass castPatient satisfactionScaphoid fracture

Substanzen

fiberglass

Autor:innen und Institutionen

  • Department of Plastic and Hand Surgery, Inselspital Bern, University of Bern, Bern, Switzerland. Electronic address: bernadette.tobler@insel.ch.
  • Colab Fribourg, Swibrace Ltd, Fribourg, Switzerland; Department of Orthopaedics and Surgery, Université libre de Bruxelles, Brussels, Belgium.
  • Colab Fribourg, Swibrace Ltd, Fribourg, Switzerland.
  • Department of Plastic and Hand Surgery, Inselspital Bern, University of Bern, Bern, Switzerland.

Förderung

  • Innosuisse Swiss Innovation Agency

Zitieren

APA

Tobler-Ammann, B., Schuind, F., Voillat, L., & Vögelin, E. (2025). Acceptability and safety of 3D printed wrist-based orthoses compared to fiberglass casts for the treatment of non-surgical distal radius- and scaphoid fractures: A randomized feasibility trial. Journal of Hand Therapy. https://doi.org/10.1016/j.jht.2024.11.004

Vancouver

Tobler-Ammann B, Schuind F, Voillat L, Vögelin E. Acceptability and safety of 3D printed wrist-based orthoses compared to fiberglass casts for the treatment of non-surgical distal radius- and scaphoid fractures: A randomized feasibility trial. Journal of Hand Therapy. 2025. doi:10.1016/j.jht.2024.11.004

BibTeX
@article{ToblerAmmann2025,
  author = {Tobler-Ammann, Bernadette and Schuind, Frédéric and Voillat, Loïc and Vögelin, Esther},
  title = {Acceptability and safety of 3D printed wrist-based orthoses compared to fiberglass casts for the treatment of non-surgical distal radius- and scaphoid fractures: A randomized feasibility trial},
  journal = {Journal of Hand Therapy},
  year = {2025},
  doi = {10.1016/j.jht.2024.11.004}
}
Kostenlos starten →