Surface roughness and gloss alteration of polished resin composites with various filler types after simulated toothbrush abrasion
Journal of Dental Sciences · 2023-07 · 18 (3) · 1016-1022
DOI: 10.1016/j.jds.2022.12.004 ↗Kurz gefasst
Fachartikel in der Zeitschrift Journal of Dental Sciences, 2023-07. Verfasst von Peng Yu und 3 weiteren Autor:innen. Beteiligte Einrichtung: Department of Cariology and Endodontology, Peking University School and Hospital of Stomatology, Beijing, China. Die Arbeit wurde bisher 21-mal zitiert (Crossref) und nennt 22 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY-NC-ND 4.0). Gefördert von: School of Stomatology, Peking University.
Abstract (Originalsprache)
Background/purpose: Few studies have focused on the influence of simulated toothbrush abrasion on the surface qualities of novel nanofilled and nanohybrid composites. The aim of the study was to evaluate the surface roughness and gloss values of resin-based composite (RBC) materials with various filler types before and after simulated toothbrush abrasion. Materials and methods: One nanofilled (Filtek Z350 XT [FT3]), two nanohybrids (Harmonize [HM] and Clearfil Majesty [CM]) and one microhybrid (Filtek Z250 [FT2]) were evaluated. Twelve specimens of each material were made and polished with silicon carbide sandpapers. Initial surface roughness and gloss values were measured as negative controls. Then, all specimens were subjected to simulated toothbrush abrasion on a custom-made apparatus. After 2000, 4000 and 8000 cycles, the surface roughness and gloss values of all specimens were tested. One additional specimen from each group was selected for scanning electron microscope (SEM) analysis.
Results
For FT3, Ra and GU values did not significantly change until after 8000 cycles during the process of toothbrushing (P > 0.05). For HM, CM and FT2, the Ra and GU values significantly decreased after 4000 and 8000 cycles of toothbrush abrasion (P < 0.05). After 8000 cycles of toothbrush abrasion, FT3 presented the lowest surface roughness and highest gloss values of all materials (P < 0.05). SEM images showed that surface textures and irregularities corresponded to the results of surface roughness and gloss.
Conclusion
Surface roughness and gloss after simulated toothbrush abrasion were material dependent. Nanofilled resin composite presented the lowest Ra values and highest GU values.
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- Department of Cariology and Endodontology, Peking University School and Hospital of Stomatology, Beijing, China.
- National Clinical Research Center for Oral Diseases & National Engineering Research Center of Oral Biomaterials and Digital Medical Devices & Beijing Key Laboratory of Digital Stomatology, Beijing, China.
- First Dental Clinical Division, Peking University School and Hospital of Stomatology, Beijing, China.
- Department of Dental Materials, Peking University School and Hospital of Stomatology, Beijing, China.
Förderung
- School of Stomatology, Peking University
Zitieren
APA
Yu, P., Yang, S. M., Xu, Y. X., & Wang, X. Y. (2023). Surface roughness and gloss alteration of polished resin composites with various filler types after simulated toothbrush abrasion. Journal of Dental Sciences, 18(3), 1016-1022. https://doi.org/10.1016/j.jds.2022.12.004
Vancouver
Yu P, Yang SM, Xu YX, Wang XY. Surface roughness and gloss alteration of polished resin composites with various filler types after simulated toothbrush abrasion. Journal of Dental Sciences. 2023;18(3):1016-1022. doi:10.1016/j.jds.2022.12.004
BibTeX
@article{Yu2023,
author = {Yu, Peng and Yang, Su-Ming and Xu, Yong-Xiang and Wang, Xiao-Yan},
title = {Surface roughness and gloss alteration of polished resin composites with various filler types after simulated toothbrush abrasion},
journal = {Journal of Dental Sciences},
year = {2023},
volume = {18},
number = {3},
pages = {1016--1022},
doi = {10.1016/j.jds.2022.12.004}
}
EUVIMED