EUVIMEDEUVIMED entdecken
Crossref

Patient-specific 3D-printed four-part interlocking mold-assisted sticky bone graft shaping in late secondary alveolar bone grafting

Y E Arslan, Y Süküt, B S Akdeniz, U Tekin

International Journal of Oral and Maxillofacial Surgery · 2026-07

DOI: 10.1016/j.ijom.2026.07.004 ↗

Kurz gefasst

Fachartikel in der Zeitschrift International Journal of Oral and Maxillofacial Surgery, 2026-07. Verfasst von Y E Arslan und 3 weiteren Autor:innen. Beteiligte Einrichtung: Department of Oral and Maxillofacial Surgery, Gulhane Faculty of Dentistry, University of Health Sciences, Ankara, Turkey. Die Arbeit nennt 13 Literaturangaben.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Accurate graft adaptation remains a major challenge in alveolar bone grafting, especially when particulate graft materials are used. This technical note presents a digital and surgical workflow for shaping a defect-matched sticky bone graft with a patient-specific three-dimensional (3D)-printed mold. Cone-beam computed tomography-based segmentation and volumetric planning were performed in 3D Slicer, and the cleft geometry was transferred to Meshmixer for mold design. A four-part mold was fabricated to allow controlled condensation of the graft material and retrieval without fragmentation. Autogenous symphyseal bone, xenogenic graft material, and platelet-rich fibrin were combined to form sticky bone, which was packed into the mold and then placed into the defect after setting. The proposed workflow integrates virtual planning, sticky bone preparation, and mold-assisted graft shaping into a single process. This technique may improve graft adaptation, simplify intraoperative handling, and support more standardized graft preparation in alveolar cleft reconstruction.

Schlagwörter

Stichwörter der Autor:innen

Alveolar bone graftingComputer-aided designCone-beam computed tomographyPlatelet-rich fibrinPrintingThree-dimensional

Autor:innen und Institutionen

  • Department of Oral and Maxillofacial Surgery, Gulhane Faculty of Dentistry, University of Health Sciences, Ankara, Turkey.
  • Department of Orthodontics, Gulhane Faculty of Dentistry, University of Health Sciences, Ankara, Turkey.
  • Department of Oral and Maxillofacial Surgery, Gulhane Faculty of Dentistry, University of Health Sciences, Ankara, Turkey. Electronic address: umutekin@gmail.com.

Zitieren

APA

Arslan, Y. E., Süküt, Y., Akdeniz, B. S., & Tekin, U. (2026). Patient-specific 3D-printed four-part interlocking mold-assisted sticky bone graft shaping in late secondary alveolar bone grafting. International Journal of Oral and Maxillofacial Surgery. https://doi.org/10.1016/j.ijom.2026.07.004

Vancouver

Arslan YE, Süküt Y, Akdeniz BS, Tekin U. Patient-specific 3D-printed four-part interlocking mold-assisted sticky bone graft shaping in late secondary alveolar bone grafting. International Journal of Oral and Maxillofacial Surgery. 2026. doi:10.1016/j.ijom.2026.07.004

BibTeX
@article{Arslan2026,
  author = {Arslan, Y E and Süküt, Y and Akdeniz, B S and Tekin, U},
  title = {Patient-specific 3D-printed four-part interlocking mold-assisted sticky bone graft shaping in late secondary alveolar bone grafting},
  journal = {International Journal of Oral and Maxillofacial Surgery},
  year = {2026},
  doi = {10.1016/j.ijom.2026.07.004}
}
Kostenlos starten →