EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Starch-Based scaffold produced by FDM 3D printing technique as Innovative and biosustainable wound dressing

Franco Dominici, Anna Imbriano, Debora Puglia, Cinzia Pagano, Francesca Luzi, Aurora Rafanelli, Alessandro Di Michele, Francesco Bonacci, Maria Rachele Ceccarini, Sara Primavilla, Andrea Valiani, Leonardo Tensi und 5 weitere

European Journal of Pharmaceutics and Biopharmaceutics · 2025-05 · 210 · 114698

DOI: 10.1016/j.ejpb.2025.114698 ↗

Kurz gefasst

Fachartikel in der Zeitschrift European Journal of Pharmaceutics and Biopharmaceutics, 2025-05. Verfasst von Franco Dominici und 16 weiteren Autor:innen. Beteiligte Einrichtung: Civil and Environmental Engineering Department, University of Perugia, UdR INSTM, 05100 Terni, Italy. Hauptthemen laut MEDLINE: Starch, Printing, Three-Dimensional, Bandages, Tissue Scaffolds. Die Arbeit wurde bisher 7-mal zitiert (Crossref) und nennt 63 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Università degli Studi di Perugia, European Union, Ministero dell’Istruzione, dell’Università e della Ricerca.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Starch is a safe biopolymer, whose use for the production of scaffolds intended for deep wounds treatment is limited, due to its low mechanical and thermal properties. For this reason, until now, it has been used in low amounts and/or in combination with other biopolymers. The aim of the study was to produce thermoplastic filaments (TPS) with high starch content, useful for scaffolds production by Fusion Deposition Modelling 3D printing technique. TPS was obtained by hot melt extrusion from a mixture of starch (70 % w/w) and glycerol (30 % w/w) combined to cationic clay montmorillonite, citric acid and magnesium stearate to improve strength and processability. The prepared scaffold was characterized and compared to other two scaffolds, where the effect of the addition of polycaprolactone (PCL) or methylsulphonylmethane (MSM) (as thermostable model drug) to the blend was evaluated. The mechanical properties were investigated by Brillouin Light Scattering. In vitro studies highlighted that the scaffolds are: i) able to absorb simulated exudates (reaching a hydration of 35 % in 7 days); ii) safe on keratinocytes (viability > 70 %) stimulating their growth; iii) able to inhibit S. pyogenes growth.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

StarchPrinting, Three-DimensionalBandagesTissue ScaffoldsWound HealingHumansPolyestersGlycerolBentonite

Stichwörter der Autor:innen

Antimicrobial activityFusion Deposition Modelling (FDM)ScaffoldStarchThermoplastic filamentWound healing

Substanzen

StarchPolyesterspolycaprolactoneGlycerolBentonite

Autor:innen und Institutionen

  • Civil and Environmental Engineering Department, University of Perugia, UdR INSTM, 05100 Terni, Italy.
  • Department of Pharmaceutical Sciences, University of Perugia 06123 Perugia, Italy.
  • Department of Pharmaceutical Sciences, University of Perugia 06123 Perugia, Italy. Electronic address: cinzia.pagano@unipg.it.
  • Department of Science and Engineering of Matter, Environment and Urban Planning, Polytechnic University of Marche, UdR INSTM, 60131 Ancona, Italy.
  • Department of Physics and Geology, University of Perugia 06123 Perugia, Italy.
  • Istituto Zooprofilattico Sperimentale dell'Umbria e delle Marche "Togo Rosati", 06126 Perugia, Italy.

Förderung

  • Università degli Studi di Perugia
  • European Union
  • Ministero dell’Istruzione, dell’Università e della Ricerca
  • Ministerio de Ciencia e Innovación
  • Ministerio de Ciencia, Innovación y Universidades
  • Università Politecnica delle Marche
  • Government of Andalusia

Zitieren

APA

Dominici, F., Imbriano, A., Puglia, D., Pagano, C., Luzi, F., Rafanelli, A., Michele, A. D., Bonacci, F., Ceccarini, M. R., Primavilla, S., Valiani, A., Tensi, L., Pérez Gutierrez, C. L., Melo Barbosa, R., Viseras, C., Ricci, M., & Perioli, L. (2025). Starch-Based scaffold produced by FDM 3D printing technique as Innovative and biosustainable wound dressing. European Journal of Pharmaceutics and Biopharmaceutics, 210, 114698. https://doi.org/10.1016/j.ejpb.2025.114698

Vancouver

Dominici F, Imbriano A, Puglia D, Pagano C, Luzi F, Rafanelli A, et al. Starch-Based scaffold produced by FDM 3D printing technique as Innovative and biosustainable wound dressing. European Journal of Pharmaceutics and Biopharmaceutics. 2025;210:114698. doi:10.1016/j.ejpb.2025.114698

BibTeX
@article{Dominici2025,
  author = {Dominici, Franco and Imbriano, Anna and Puglia, Debora and Pagano, Cinzia and Luzi, Francesca and Rafanelli, Aurora and Michele, Alessandro Di and Bonacci, Francesco and Ceccarini, Maria Rachele and Primavilla, Sara and Valiani, Andrea and Tensi, Leonardo and Pérez Gutierrez, Carmen Laura and Melo Barbosa, Raquel De and Viseras, César and Ricci, Maurizio and Perioli, Luana},
  title = {Starch-Based scaffold produced by FDM 3D printing technique as Innovative and biosustainable wound dressing},
  journal = {European Journal of Pharmaceutics and Biopharmaceutics},
  year = {2025},
  volume = {210},
  pages = {114698},
  doi = {10.1016/j.ejpb.2025.114698}
}
Kostenlos starten →