EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Design and evaluation of curcumin-loaded poloxamer hydrogels as injectable depot formulations

Ashok David Jose, Kea Leigh Foo, Grace Hu, Linda Ngar, Bovinae Ryda, Jagdish Jaiswal, Zimei Wu, Priyanka Agarwal, Sachin Sunil Thakur

European Journal of Pharmaceutics and Biopharmaceutics · 2024

DOI: 10.1016/j.ejpb.2024.114372 ↗

Kurz gefasst

Fachartikel in der Zeitschrift European Journal of Pharmaceutics and Biopharmaceutics, 2024. Verfasst von Ashok David Jose und 8 weiteren Autor:innen. Beteiligte Einrichtung: School of Pharmacy, Faculty of Medical and Health Sciences, University of Auckland, Private Bag 92019, Auckland 1142, New Zealand. Hauptthemen laut MEDLINE: Curcumin, Hydrogels, Poloxamer, Polyethylene Glycols. Die Arbeit wurde bisher 17-mal zitiert (Crossref) und nennt 56 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: University of Auckland, Maurice and Phyllis Paykel Trust.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Poloxamer hydrogels are of interest as injectable depot delivery systems. However, their use for delivering hydrophobic drugs, such as curcumin, is limited due to poor loading capacity. Here, we evaluated the influence of incorporating hydrophobic medium chain triglycerides (MCT) or amphiphilic polyethylene glycol 400 (PEG400) on the physicochemical properties, drug loading, and in vitro compatibility of a curcumin-loaded poloxamer hydrogel. Poloxamer 407 and 188 hydrogel formulations (16:6 w/w) were prepared and MCT and PEG400 (saturated with curcumin) were added to these systems, either alone or in combination, up to a 10 % w/w additive solvent load. Formulation viscoelasticity, gelation behaviour, injectability, morphology and release profiles were assessed. The cytocompatibility of the formulations was also assessed on dermal fibroblasts (HDFn). Both additives increased curcumin loading into the formulation. Addition of MCT to the hydrogel significantly increased its gelation speed, while PEG400 had a less profound impact. Both additive solvents increased the force required to inject the formulation. PEG400 containing systems were single phase, whereas MCT addition created emulsion systems. All formulations released ∼20-30 % of their loaded curcumin in a sustained fashion over 24 h. The modified hydrogel systems showed good biocompatibility on cells when administering up to ∼100-150 µM curcumin into the culture. This study addresses a key limitation in loading hydrophobic drugs into hydrogels and provides a strategy to enhance drug loading and performance of hydrogels by integrating additives such as MCT and PEG400 into the systems.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

CurcuminHydrogelsPoloxamerPolyethylene GlycolsFibroblastsHumansDelayed-Action PreparationsDrug LiberationHydrophobic and Hydrophilic InteractionsChemistry, PharmaceuticalTriglyceridesInjectionsDrug Delivery SystemsDrug CompoundingDrug Carriers

Stichwörter der Autor:innen

CurcuminEmulsionHydrogelMCTP188P407PEG400PoloxamerSustained drug delivery

Substanzen

CurcuminHydrogelsPoloxamerPolyethylene GlycolsDelayed-Action Preparationspolyethylene glycol 400TriglyceridesDrug Carriers

Autor:innen und Institutionen

  • School of Pharmacy, Faculty of Medical and Health Sciences, University of Auckland, Private Bag 92019, Auckland 1142, New Zealand.
  • Auckland Cancer Society Research Centre, Faculty of Medical and Health Sciences, University of Auckland, Private Bag 92019, Auckland 1142, New Zealand.
  • Buchanan Ocular Therapeutics Unit, Department of Ophthalmology, New Zealand National Eye Centre, Faculty of Medical and Health Sciences, University of Auckland, Private Bag 92019, Auckland 1142, New Zealand. Electronic…
  • School of Pharmacy, Faculty of Medical and Health Sciences, University of Auckland, Private Bag 92019, Auckland 1142, New Zealand. Electronic address: s.thakur@auckland.ac.nz.

Förderung

  • University of Auckland
  • Maurice and Phyllis Paykel Trust

Zitieren

APA

Jose, A. D., Foo, K. L., Hu, G., Ngar, L., Ryda, B., Jaiswal, J., Wu, Z., Agarwal, P., & Thakur, S. S. (2024). Design and evaluation of curcumin-loaded poloxamer hydrogels as injectable depot formulations. European Journal of Pharmaceutics and Biopharmaceutics. https://doi.org/10.1016/j.ejpb.2024.114372

Vancouver

Jose AD, Foo KL, Hu G, Ngar L, Ryda B, Jaiswal J, et al. Design and evaluation of curcumin-loaded poloxamer hydrogels as injectable depot formulations. European Journal of Pharmaceutics and Biopharmaceutics. 2024. doi:10.1016/j.ejpb.2024.114372

BibTeX
@article{Jose2024,
  author = {Jose, Ashok David and Foo, Kea Leigh and Hu, Grace and Ngar, Linda and Ryda, Bovinae and Jaiswal, Jagdish and Wu, Zimei and Agarwal, Priyanka and Thakur, Sachin Sunil},
  title = {Design and evaluation of curcumin-loaded poloxamer hydrogels as injectable depot formulations},
  journal = {European Journal of Pharmaceutics and Biopharmaceutics},
  year = {2024},
  doi = {10.1016/j.ejpb.2024.114372}
}
Kostenlos starten →