EUVIMEDEUVIMED entdecken
Crossref

Needles to Spheres: Evaluation of inkjet printing as a particle shape enhancement tool

Manuel Zettl, Christina Winter, Jérôme Mantanus, Eftychios Hadjittofis, Sandrine Rome, Gerd Leitinger, Wen-Kai Hsiao, Eva Roblegg, Joana T Pinto, Martin Spoerk

European Journal of Pharmaceutics and Biopharmaceutics · 2023

DOI: 10.1016/j.ejpb.2023.01.016 ↗

Kurz gefasst

Fachartikel in der Zeitschrift European Journal of Pharmaceutics and Biopharmaceutics, 2023. Verfasst von Manuel Zettl und 9 weiteren Autor:innen. Beteiligte Einrichtung: Research Center Pharmaceutical Engineering GmbH, Inffeldgasse 13, 8010, Graz. Hauptthemen laut MEDLINE: Excipients, Needles. Die Arbeit wurde bisher 5-mal zitiert (Crossref) und nennt 72 Literaturangaben.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Active pharmaceutical ingredients (APIs) often reveal shapes challenging to process, e.g. acicular structures, and exhibit reduced bioavailability induced by slow dissolution rate. Leveraging the API particles' surface and bulk properties offers an attractive pathway to circumvent these challenges. Inkjet printing is an attractive processing technique able to tackle these limitations already in initial stages when little material is available, while particle properties are maintained over the entire production scale. Additionally, it is applicable to a wide range of formulations and offers the possibility of co-processing with a variety of excipients to improve the API's bioavailability. This study addresses the optimization of particle shapes for processability enhancement and demonstrates the successful application of inkjet printing to engineer spherical lacosamide particles, which are usually highly acicular. By optimizing the ink formulation, adapting the substrate-liquid interface and tailoring the heat transfer to the particle, spherical particles in the vicinity of 100 µm, with improved flow properties compared to the bulk material, were produced. Furthermore, the particle size was tailored reproducibly by adjusting the deposited ink volume per cycle and the number of printing cycles. Therefore, the present study shows a novel, reliable, scalable and economical strategy to overcome challenging particle morphologies by co-processing an API with suitable excipients.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

ExcipientsNeedlesPrintingParticle SizePrinting, Three-Dimensional

Stichwörter der Autor:innen

Acicular drugsInkjet printingParticle EngineeringParticle morphologyPersonalized manufacturing

Substanzen

Excipients

Autor:innen und Institutionen

  • Research Center Pharmaceutical Engineering GmbH, Inffeldgasse 13, 8010, Graz.
  • UCB S.A, Allée de la Recherche, 60, 1070 Brussels, Belgium.
  • Division of Cell Biology, Histology and Embryology, Gottfried Schatz Research Center, Medical University of Graz, Neue Stiftingtalstrasse 6/II, 8010, Graz, Austria.
  • Research Center Pharmaceutical Engineering GmbH, Inffeldgasse 13, 8010, Graz; Institute of Pharmaceutical Sciences, Pharmaceutical Technology and Biopharmacy, University of Graz, Universitätsplatz 1, 8010 Graz, Austria.
  • Research Center Pharmaceutical Engineering GmbH, Inffeldgasse 13, 8010, Graz. Electronic address: martin.spoerk@rcpe.at.

Zitieren

APA

Zettl, M., Winter, C., Mantanus, J., Hadjittofis, E., Rome, S., Leitinger, G., Hsiao, W. K., Roblegg, E., Pinto, J. T., & Spoerk, M. (2023). Needles to Spheres: Evaluation of inkjet printing as a particle shape enhancement tool. European Journal of Pharmaceutics and Biopharmaceutics. https://doi.org/10.1016/j.ejpb.2023.01.016

Vancouver

Zettl M, Winter C, Mantanus J, Hadjittofis E, Rome S, Leitinger G, et al. Needles to Spheres: Evaluation of inkjet printing as a particle shape enhancement tool. European Journal of Pharmaceutics and Biopharmaceutics. 2023. doi:10.1016/j.ejpb.2023.01.016

BibTeX
@article{Zettl2023,
  author = {Zettl, Manuel and Winter, Christina and Mantanus, Jérôme and Hadjittofis, Eftychios and Rome, Sandrine and Leitinger, Gerd and Hsiao, Wen-Kai and Roblegg, Eva and Pinto, Joana T and Spoerk, Martin},
  title = {Needles to Spheres: Evaluation of inkjet printing as a particle shape enhancement tool},
  journal = {European Journal of Pharmaceutics and Biopharmaceutics},
  year = {2023},
  doi = {10.1016/j.ejpb.2023.01.016}
}
Kostenlos starten →