Experimental analysis and optimization of an indirect solar dryer integrated with heat exchanger for enhanced exhaust air utilization
Case Studies in Thermal Engineering · 2025-11 · 75 · 107101
DOI: 10.1016/j.csite.2025.107101 ↗Kurz gefasst
Fachartikel in der Zeitschrift Case Studies in Thermal Engineering, 2025-11. Verfasst von M.K. Murthi und 3 weiteren Autor:innen. Die Arbeit wurde bisher 7-mal zitiert (Crossref) und nennt 30 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY-NC-ND 4.0). Gefördert von: King Khalid University.
Abstract (Originalsprache)
Increased global demand for energy amid the world fear of dwindling energy, carbon emissions, and food preservation losses exceeding 30% of agricultural output on a global scale has propelled the call to replace less sustainable post-harvest technologies with alternatives offering reduced or no emissions. Among them- solar drying has come out as a promising renewable solution. However, the traditional systems encounter problems including low thermal efficiency, high heat losses, and high duration of drying phases. The objective of this study is to experimentally analyse and optimize the performance of an indirect solar dryer coupled with a heat exchanger for improve exhaust air utilization. The developed system consists in a 5 m 2 flat-plate solar collector, a 0.5 m 3 drying chamber, a cross-flow plate-fin heat exchanger with an effectiveness of 65% to recover and recycle thermal energy from exhaust air. Experiments were performed by manipulating levels of airflow rate (0.02–0.06 m 3 /s), recycled exhaust air (0–50%), layer thickness of products on bed (1–4 cm). Other parameters such as drying air temperature, rate of moisture removal, SMER, thermal efficiency and exergy efficiency were computed at solar radiation intensities varying from 500 to 850 W/m 2 . Major observations show that the incorporation of the heat exchanger managed to maintain an unvaryingly higher temperature of the drying air by 8–12°C, with this amounting to a figure of 20.4% saving of the total drying time. The thermal efficiency was raised from 48.2% to 62.1% and the energy recovery from the exhaust air up to 35 %. Maximum Specific Moisture Extraction Rate (SMER) was attained on best solar conditions at 0.48 kg/kWh. Relative humidity in the chamber itself was maintained effectively below 34.8%, improving drying efficiency by 11.7% relative to the baseline. Optimization of the process was carried out using Response Surface Methodology (RSM), resulting in second-order regression models with high coefficients of determination (R 2 ) greater than 0.96. RSM predictions of optimal conditions, namely the air flow rate of 0.041 m 3 /s, recycle of 30% of exhaust air and the layer thickness of 2 cm resulted in maximum drying performance and preservation of product quality with experimental validation errors being not more than ±5 %. This research showed a 14 kg reduction of CO 2 emissions from ten drying cycles, a scalable and energy efficient pathway for sustainable agricultural processing and utilization of renewable energies.
Förderung
- King Khalid University
Zitieren
APA
Murthi, M., Munimathan, A., Kareemullah, M., & Khan, T. Y. (2025). Experimental analysis and optimization of an indirect solar dryer integrated with heat exchanger for enhanced exhaust air utilization. Case Studies in Thermal Engineering, 75, 107101. https://doi.org/10.1016/j.csite.2025.107101
Vancouver
Murthi M, Munimathan A, Kareemullah M, Khan TY. Experimental analysis and optimization of an indirect solar dryer integrated with heat exchanger for enhanced exhaust air utilization. Case Studies in Thermal Engineering. 2025;75:107101. doi:10.1016/j.csite.2025.107101
BibTeX
@article{Murthi2025,
author = {Murthi, M.K. and Munimathan, Arunkumar and Kareemullah, Md and Khan, T.M. Yunus},
title = {Experimental analysis and optimization of an indirect solar dryer integrated with heat exchanger for enhanced exhaust air utilization},
journal = {Case Studies in Thermal Engineering},
year = {2025},
volume = {75},
pages = {107101},
doi = {10.1016/j.csite.2025.107101}
}
EUVIMED