Synergy of silica sand and waste plastics as thermoplastic composites on abrasive wear characteristics under conditions of different loads and sliding speeds
Chemosphere · 2023
DOI: 10.1016/j.chemosphere.2023.138233 ↗Kurz gefasst
Fachartikel in der Zeitschrift Chemosphere, 2023. Verfasst von Ashish Soni und 10 weiteren Autor:innen. Beteiligte Einrichtung: Department of Mechanical Engineering, National Institute of Technology, Agartala, Tripura, 799046, India. Hauptthemen laut MEDLINE: Plastics, Sand. Die Arbeit wurde bisher 24-mal zitiert (Crossref) und nennt 92 Literaturangaben. Gefördert von: King Saud University.
Abstract (Originalsprache)
The diverse nature of polymers with attractive properties has replaced the conventional materials with polymeric composites. The present study was sought to evaluate the wear performance of thermoplastic-based composites under the conditions of different loads and sliding speeds. In the present study, nine different composites were developed by using low-density polyethylene (LDPE), high-density polyethylene (HDPE) and polyethylene terephthalate (PET) with partial sand replacements i.e., 0, 30, 40, and 50 wt%. The abrasive wear was evaluated as per the ASTM G65 standard test for abrasive wear through a dry-sand rubber wheel apparatus under the applied loads of 34.335, 56.898, 68.719, 79.461 and 90.742 (N) and sliding speeds of 0.5388, 0.7184, 0.8980, 1.0776 and 1.4369 (m/s). The optimum density and compressive strength were obtained to be 2.0555 g/cm3 and 46.20 N/mm2, respectively for the composites HDPE60 and HDPE50 respectively. The minimum value of abrasive wear were found to 0.02498, 0.03430, 0.03095, 0.09020 and 0.03267 (cm3) under the considered loads of 34.335, 56.898, 68.719, 79.461 and 90.742 (N), respectively. Moreover, the composites LDPE50, LDPE100, LDPE100, LDPE50PET20 and LDPE60 showed a minimum abrasive wear of 0.03267, 0.05949, 0.05949, 0.03095 and 0.10292 at the sliding speeds of 0.5388, 0.7184, 0.8980, 1.0776 and 1.4369 (m/s), respectively. The wear response varied non-linearly with the conditions of loads and sliding speeds. Micro-cutting, plastic deformations, fiber peelings, etc. were included as the possible wear mechanism. The possible correlations between wear and mechanical properties, and throughout discussions for wear behaviors through the morphological analyses of the worn-out surfaces were provided.
Schlagwörter
MeSH-Schlagwörter (MEDLINE)
Stichwörter der Autor:innen
Substanzen
Autor:innen und Institutionen
- Department of Mechanical Engineering, National Institute of Technology, Agartala, Tripura, 799046, India.
- Department of Petroleum Engineering, Universiti Teknologi PETRONAS, Bandar Seri Iskandar, Perak, 32610, Malaysia; Institute of Hydrocarbon Recovery, Universiti Teknologi PETRONAS, Bandar Seri Iskandar, Perak, 32610, Mal…
- Faculty of Architecture and Urbanism, UTE University, Calle Rumipamba S/N and Bourgeois, Quito, Ecuador; Department of Biomaterials, Saveetha Dental College and Hospital, Saveetha Institute of Medical and Technical Scie…
- Department of Mechanical Engineering, Universiti Teknologi PETRONAS, Bandar Seri Iskandar, Perak, 32610, Malaysia.
- Department of Electrical and Electronics Engineering, Universiti Teknologi PETRONAS, Bandar Seri Iskandar, 32610, Perak, Malaysia.
- Engineering Department, Razak Faculty of Technology & Informatics, Universiti Teknologi Malaysia, Jalan Sultan Yahya Petra, Kuala Lumpur, 54100, Malaysia.
Förderung
- King Saud University
Zitieren
APA
Soni, A., Das, P. K., Yusuf, M., Ridha, S., Kamyab, H., Alam, M. A., Masood, F., Chelliapan, S., Ubaidullah, M., Pandit, B., & Prakash, C. (2023). Synergy of silica sand and waste plastics as thermoplastic composites on abrasive wear characteristics under conditions of different loads and sliding speeds. Chemosphere. https://doi.org/10.1016/j.chemosphere.2023.138233
Vancouver
Soni A, Das PK, Yusuf M, Ridha S, Kamyab H, Alam MA, et al. Synergy of silica sand and waste plastics as thermoplastic composites on abrasive wear characteristics under conditions of different loads and sliding speeds. Chemosphere. 2023. doi:10.1016/j.chemosphere.2023.138233
BibTeX
@article{Soni2023,
author = {Soni, Ashish and Das, Pankaj Kumar and Yusuf, Mohammad and Ridha, Syahrir and Kamyab, Hesam and Alam, Mohammad Azad and Masood, Faisal and Chelliapan, Shreeshivadasan and Ubaidullah, Mohd and Pandit, Bidhan and Prakash, Chander},
title = {Synergy of silica sand and waste plastics as thermoplastic composites on abrasive wear characteristics under conditions of different loads and sliding speeds},
journal = {Chemosphere},
year = {2023},
doi = {10.1016/j.chemosphere.2023.138233}
}
EUVIMED