EUVIMEDEUVIMED entdecken
Open Access

Investigating environmentally persistent free radicals (EPFRs) emissions of 3D printing process

Farhana Hasan, Phillip M Potter, Souhail R Al-Abed, Joanna Matheson, Slawomir M Lomnicki

Chemical Engineering Journal · 2024-01 · 480 · 148158

DOI: 10.1016/j.cej.2023.148158 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Chemical Engineering Journal, 2024-01. Verfasst von Farhana Hasan und 4 weiteren Autor:innen. Beteiligte Einrichtung: Department of Environmental Sciences, Louisiana State University, Baton Rouge, LA 70803, USA. Die Arbeit wurde bisher 4-mal zitiert (Crossref) und nennt 68 Literaturangaben. Der Volltext ist frei in PubMed Central verfügbar. Gefördert von: Intramural EPA.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

In recent years, the emission of particles and gaseous pollutants from 3D printing has attracted much attention due to potential health risks. This study investigated the generation of environmentally persistent free radicals (EPFRs, organic free radicals stabilized on or inside particles) in total particulate matter (TPM) released during the 3D printing process. Commercially available 3D printer filaments, made of acrylonitrile-butadiene-styrene (ABS) in two different colors and metal content, ABS-blue (19.66 μg/g Cu) and ABS-black (3.69 μg/g Fe), were used for printing. We hypothesized that the metal content/composition of the filaments contributes not only to the type and number of EPFRs in TPM emissions, but also impacts the overall yield of TPM emissions. TPM emissions during printing with ABS-blue (11.28 μg/g of printed material) were higher than with ABS-black (7.29 μg/g). Electron paramagnetic resonance (EPR) spectroscopy, employed to measure EPFRs in TPM emissions of both filaments, revealed higher EPFR concentrations in ABS-blue TPM (6.23 × 1017 spins/g) than in ABS-black TPM (9.72 × 1016 spins/g). The presence of copper in the ABS-blue contributed to the formation of mostly oxygen-centered EPFR species with a g-factor of ~2.0041 and a lifetime of 98 days. The ABS-black EPFR signal had a lower g-factor of ~2.0011, reflecting the formation of superoxide radicals during the printing process, which were shown to have an "estimated tentative" lifetime of 26 days. Both radical species (EPFRs and superoxides) translate to a potential health risk through inhalation of emitted particles.

Schlagwörter

Stichwörter der Autor:innen

3D printingElectron paramagnetic resonanceEnvironmentally persistent free radicalsFilamentsFused filament fabricationMetal additivesTotal particulate matter

Autor:innen und Institutionen

  • Department of Environmental Sciences, Louisiana State University, Baton Rouge, LA 70803, USA.
  • U.S. Environmental Protection Agency, Office of Research and Development, Center for Environmental Research and Emergency Response, Cincinnati, OH 45268, USA.
  • U.S. Consumer Product and Safety Commission, Health Sciences Directorate, Rockville, MD 20850, USA.

Förderung

  • Intramural EPA

Zitieren

APA

Hasan, F., Potter, P. M., Al-Abed, S. R., Matheson, J., & Lomnicki, S. M. (2024). Investigating environmentally persistent free radicals (EPFRs) emissions of 3D printing process. Chemical Engineering Journal, 480, 148158. https://doi.org/10.1016/j.cej.2023.148158

Vancouver

Hasan F, Potter PM, Al-Abed SR, Matheson J, Lomnicki SM. Investigating environmentally persistent free radicals (EPFRs) emissions of 3D printing process. Chemical Engineering Journal. 2024;480:148158. doi:10.1016/j.cej.2023.148158

BibTeX
@article{Hasan2024,
  author = {Hasan, Farhana and Potter, Phillip M and Al-Abed, Souhail R and Matheson, Joanna and Lomnicki, Slawomir M},
  title = {Investigating environmentally persistent free radicals (EPFRs) emissions of 3D printing process},
  journal = {Chemical Engineering Journal},
  year = {2024},
  volume = {480},
  pages = {148158},
  doi = {10.1016/j.cej.2023.148158}
}
Kostenlos starten →