EUVIMEDEUVIMED entdecken
Crossref

Lab on fiber: A 3D-printed fiber-tip microprobe for synchronous detection of doxorubicin concentration and temperature

Like Li, Yi Li, Lu Cai, Xiaoming Chen, Dan Li, Bo Han, Ya-Nan Zhang, Yong Zhao

Biosensors and Bioelectronics · 2027-01 · 316 · 119316

DOI: 10.1016/j.bios.2026.119316 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Biosensors and Bioelectronics, 2027-01. Verfasst von Like Li und 7 weiteren Autor:innen. Beteiligte Einrichtung: College of Information Science and Engineering, Northeastern University, Shenyang, 110819, China; Hebei Key Laboratory of Micro-Nano Precision Optica…. Hauptthemen laut MEDLINE: Doxorubicin, Surface Plasmon Resonance, Biosensing Techniques, Antibiotics, Antineoplastic. Die Arbeit wurde bisher 1-mal zitiert (Crossref) und nennt 36 Literaturangaben. Gefördert von: Fundamental Research Funds for the Central Universities, Natural Science Foundation of Hebei Province, National Natural Science Foundation of China.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Accurate monitoring of doxorubicin (DOX) is important for individualized chemotherapy, yet conventional fiber-optic surface plasmon resonance (SPR) sensors are often limited by large probe dimensions and temperature cross-sensitivity. In this paper, a compact fiber-tip microprobe that integrates SPR and Fabry-Perot interference (FPI) for synchronous detection of DOX concentration and temperature is reported. The microprobe is composed of a square frustum-similar structure, which is directly printed on the end face of a single-mode fiber by femtosecond laser-induced two-photon polymerization. By optimizing the structural parameters, SPR and FPI are simultaneously excited within the 24 μm-high microprobe. The sensing surface is further functionalized with the DOX-specific aptamer to enable selective molecular recognition. In the range of 0-100 μM DOX, the SPR and FPI channels exhibit sensitivities of 0.075 and 0.060 nm/μM, respectively, with corresponding limits of detection of 8.8 and 19.1 μM. Over 28-40 °C, the SPR and FPI temperature sensitivities are -0.66 and -0.61 nm/°C, respectively. A dual-parameter decoupling matrix enabled simultaneous determination of DOX concentration and temperature. The microprobe also showed satisfactory stability and selectivity, demonstrating its potential for miniaturized therapeutic drug monitoring.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

DoxorubicinSurface Plasmon ResonanceBiosensing TechniquesAntibiotics, AntineoplasticTemperaturePrinting, Three-DimensionalFiber Optic TechnologyEquipment DesignLimit of DetectionAptamers, NucleotideHumans

Stichwörter der Autor:innen

3D printingDoxorubicinFabry-Perot interferenceFiber-optic sensorSurface plasmon resonance

Substanzen

DoxorubicinAntibiotics, AntineoplasticAptamers, Nucleotide

Autor:innen und Institutionen

  • College of Information Science and Engineering, Northeastern University, Shenyang, 110819, China; Hebei Key Laboratory of Micro-Nano Precision Optical Sensing and Measurement Technology, Qinhuangdao, 066004, China. Elec…
  • College of Information Science and Engineering, Northeastern University, Shenyang, 110819, China; Hebei Key Laboratory of Micro-Nano Precision Optical Sensing and Measurement Technology, Qinhuangdao, 066004, China.
  • College of Information Science and Engineering, Northeastern University, Shenyang, 110819, China; Hebei Key Laboratory of Micro-Nano Precision Optical Sensing and Measurement Technology, Qinhuangdao, 066004, China; Stat…

Förderung

  • Fundamental Research Funds for the Central Universities
  • Natural Science Foundation of Hebei Province
  • National Natural Science Foundation of China

Zitieren

APA

Li, L., Li, Y., Cai, L., Chen, X., Li, D., Han, B., Zhang, Y. N., & Zhao, Y. (2027). Lab on fiber: A 3D-printed fiber-tip microprobe for synchronous detection of doxorubicin concentration and temperature. Biosensors and Bioelectronics, 316, 119316. https://doi.org/10.1016/j.bios.2026.119316

Vancouver

Li L, Li Y, Cai L, Chen X, Li D, Han B, et al. Lab on fiber: A 3D-printed fiber-tip microprobe for synchronous detection of doxorubicin concentration and temperature. Biosensors and Bioelectronics. 2027;316:119316. doi:10.1016/j.bios.2026.119316

BibTeX
@article{Li2027,
  author = {Li, Like and Li, Yi and Cai, Lu and Chen, Xiaoming and Li, Dan and Han, Bo and Zhang, Ya-Nan and Zhao, Yong},
  title = {Lab on fiber: A 3D-printed fiber-tip microprobe for synchronous detection of doxorubicin concentration and temperature},
  journal = {Biosensors and Bioelectronics},
  year = {2027},
  volume = {316},
  pages = {119316},
  doi = {10.1016/j.bios.2026.119316}
}
Kostenlos starten →