EUVIMEDEUVIMED entdecken
Crossref

Insights into the structural characteristics of cellulose for 5‑hydroxymethylfurfural production

Ning Li, Chengyu Dong, Lujiang Xu, Wei Chen, Lin Chen, Zhen Fang, Chunxiao Gong

Bioresource Technology · 2026-11 · 136274

DOI: 10.1016/j.biortech.2026.136274 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Bioresource Technology, 2026-11. Verfasst von Ning Li und 6 weiteren Autor:innen. Beteiligte Einrichtung: Biomass Group, College of Engineering, Nanjing Agricultural University, No. 666, Binjiang Avenue, Nanjing 211899, China. Die Arbeit nennt 54 Literaturangaben. Gefördert von: Hainan Province Natural Science Foundation, National Natural Science Foundation of China.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

The conversion of cellulose into 5-hydroxymethylfurfural (HMF) represents a promising strategy for high-value valorization of lignocellulosic biomass, but its highly crystalline structure significantly compromises the production efficiency. To investigate the effect of structural properties of cellulose on HMF production, various treatments of microcrystalline cellulose, including ball milling (BM), deep eutectic solvents (DES), ethylenediamine, glycerol, phosphoric acid, and sodium hydroxide were applied to modify cellulose polymorphs (types I-IV), crystallinity, and degree of polymerization (DP). Results showed that transforming cellulose I into polymorphs II or III enhanced the HMF production efficiency. Cellulose II achieved a 24.4 % HMF yield in 60 min at 160 °C, reaching a similar yield to cellulose I (24.6 % after 90 min) in a much shorter time. Compared to cellulose I, cellulose III achieved a significantly higher HMF yield of 30.7 % in only 30 min at 160 °C, representing a substantial reduction in reaction time. In contrast, cellulose IV retained high crystallinity and had nearly no effect on HMF production. BM and DES effectively reduced cellulose crystallinity and achieved HMF yields of 50.0 % and 42.6 %, respectively. Results demonstrate that HMF yield correlates negatively with both crystallinity and DP, suggesting that disordered cellulose with shorter chains facilitates catalyst access and subsequent conversion. Overall, modifying the cellulose structure by decreasing crystallinity and DP can greatly enhance conversion efficiency. This study provides a fundamental understanding of cellulose properties for further conversion into HMF and guides the design of biomass pretreatment systems.

Schlagwörter

Stichwörter der Autor:innen

5-HydroxymethylfurfuralCellulose crystallinityDegrees of polymerizationPretreatmentsSolid-state (13)C NMR

Autor:innen und Institutionen

  • Biomass Group, College of Engineering, Nanjing Agricultural University, No. 666, Binjiang Avenue, Nanjing 211899, China.
  • Biomass Group, College of Engineering, Nanjing Agricultural University, No. 666, Binjiang Avenue, Nanjing 211899, China. Electronic address: gongchunxiao@njau.edu.cn.

Förderung

  • Hainan Province Natural Science Foundation
  • National Natural Science Foundation of China

Zitieren

APA

Li, N., Dong, C., Xu, L., Chen, W., Chen, L., Fang, Z., & Gong, C. (2026). Insights into the structural characteristics of cellulose for 5‑hydroxymethylfurfural production. Bioresource Technology, 136274. https://doi.org/10.1016/j.biortech.2026.136274

Vancouver

Li N, Dong C, Xu L, Chen W, Chen L, Fang Z, et al. Insights into the structural characteristics of cellulose for 5‑hydroxymethylfurfural production. Bioresource Technology. 2026:136274. doi:10.1016/j.biortech.2026.136274

BibTeX
@article{Li2026,
  author = {Li, Ning and Dong, Chengyu and Xu, Lujiang and Chen, Wei and Chen, Lin and Fang, Zhen and Gong, Chunxiao},
  title = {Insights into the structural characteristics of cellulose for 5‑hydroxymethylfurfural production},
  journal = {Bioresource Technology},
  year = {2026},
  pages = {136274},
  doi = {10.1016/j.biortech.2026.136274}
}
Kostenlos starten →