Shear bond strength of orthodontic brackets bonded with primer-incorporated orthodontic adhesives and unpolymerized 3-dimensional printing materials on 3-dimensional-printed crowns
American Journal of Orthodontics and Dentofacial Orthopedics · 2024
DOI: 10.1016/j.ajodo.2024.01.013 ↗Kurz gefasst
Fachartikel in der Zeitschrift American Journal of Orthodontics and Dentofacial Orthopedics, 2024. Verfasst von Yukyung Choi und 5 weiteren Autor:innen. Beteiligte Einrichtung: Department of Dental Biomaterials Science, Dental Research Institute, School of Dentistry, Seoul National University, Seoul, South Korea. Hauptthemen laut MEDLINE: Printing, Three-Dimensional, Shear Strength, Orthodontic Brackets, Crowns. Die Arbeit wurde bisher 9-mal zitiert (Crossref) und nennt 29 Literaturangaben. Gefördert von: Ministry of Food and Drug Safety, Ministry of Trade, Industry and Energy, Ministry of Science, ICT and Future Planning.
Abstract (Originalsprache)
INTRODUCTION: The use of 3-dimensional (3D) printing techniques in fabricating crowns has increased the demand for bracket bonding onto these surfaces. The objective was to evaluate the shear bond strength (SBS) of orthodontic brackets bonded onto 3D-printed crowns using primer-incorporated orthodontic adhesives and 3D printing materials as orthodontic adhesives. METHODS: A total of 160 crowns were printed with two 3D printing materials, DentaTOOTH (Asiga, Sydney, Australia) (group A) and NextDent C&B Micro Filled Hybrid (3D Systems, Soesterberg, Netherlands) (group N). Each group was randomly divided into 4 adhesive subgroups (n = 20): Transbond XT (for groups A [ATX] and N [NTX]; 3M Unitek, Monrovia, Calif), Ortho Connect (for groups A [AOC] and N [NOC]; GC Corporation., Tokyo, Japan), Orthomite LC (for groups A [AOM] and N [NOM]; Sun Medical, Co Ltd, Moriyama, Shiga, Japan), and unpolymerized liquid state of 3D printing resin (for groups A [AA] and N [NN]). SBS was measured with a universal testing machine at a crosshead speed of 0.5 mm/min. The adhesive remnant index and the mode of failure were analyzed under the microscope. Statistical analysis was performed at a significance level of α = 0.05. RESULTS: When used as adhesives (AA and NN), 3D printing materials showed no statistically significant difference in SBS compared with Transbond XT (ATX and NTX, respectively). In group N, NN showed a significantly higher SBS than primer-incorporated orthodontic adhesives (NOC and NOM; P
Schlagwörter
MeSH-Schlagwörter (MEDLINE)
Substanzen
Autor:innen und Institutionen
- Department of Dental Biomaterials Science, Dental Research Institute, School of Dentistry, Seoul National University, Seoul, South Korea.
- Harvard Medical School and Wellman Center for Photomedicine, Massachusetts General Hospital, Cambridge, Mass.
- Department of Oral Health Sciences, Faculty of Dentistry, University of British Columbia, Vancouver, British Columbia, Canada.
- Department of Oral Anatomy, Dental Research Institute, Center for Future Dentistry, School of Dentistry, Seoul National University, Seoul, South Korea.
- Department of Dental Biomaterials Science, Dental Research Institute, School of Dentistry, Seoul National University, Seoul, South Korea. Electronic address: den533@snu.ac.kr.
Förderung
- Ministry of Food and Drug Safety
- Ministry of Trade, Industry and Energy
- Ministry of Science, ICT and Future Planning
- Ministry of Health and Welfare
Zitieren
APA
Choi, Y., Moon, W., Manso, A. P., Park, Y. S., Lim, B. S., & Chung, S. H. (2024). Shear bond strength of orthodontic brackets bonded with primer-incorporated orthodontic adhesives and unpolymerized 3-dimensional printing materials on 3-dimensional-printed crowns. American Journal of Orthodontics and Dentofacial Orthopedics. https://doi.org/10.1016/j.ajodo.2024.01.013
Vancouver
Choi Y, Moon W, Manso AP, Park YS, Lim BS, Chung SH. Shear bond strength of orthodontic brackets bonded with primer-incorporated orthodontic adhesives and unpolymerized 3-dimensional printing materials on 3-dimensional-printed crowns. American Journal of Orthodontics and Dentofacial Orthopedics. 2024. doi:10.1016/j.ajodo.2024.01.013
BibTeX
@article{Choi2024,
author = {Choi, Yukyung and Moon, Wonjoon and Manso, Adriana P and Park, Young-Seok and Lim, Bum-Soon and Chung, Shin Hye},
title = {Shear bond strength of orthodontic brackets bonded with primer-incorporated orthodontic adhesives and unpolymerized 3-dimensional printing materials on 3-dimensional-printed crowns},
journal = {American Journal of Orthodontics and Dentofacial Orthopedics},
year = {2024},
doi = {10.1016/j.ajodo.2024.01.013}
}
EUVIMED