Additively manufactured biodegradable Zn-Mn-based implants with an unprecedented balance of strength and ductility
Acta Biomaterialia · 2025-04 · 196 · 506-522
DOI: 10.1016/j.actbio.2025.02.047 ↗Kurz gefasst
Fachartikel in der Zeitschrift Acta Biomaterialia, 2025-04. Verfasst von Chengcong Huang und 12 weiteren Autor:innen. Beteiligte Einrichtung: Beijing Advanced Innovation Center for Materials Genome Engineering, School of Materials Science and Engineering, University of Science and Technolog…. Hauptthemen laut MEDLINE: Zinc, Alloys, Absorbable Implants, Manganese. Die Arbeit wurde bisher 39-mal zitiert (Crossref) und nennt 89 Literaturangaben. Gefördert von: National Key Research and Development Program of China, Beijing Natural Science Foundation, Beijing Nova Program.
Abstract (Originalsprache)
Additively manufactured (AM) biodegradable zinc alloys hold huge potential as promising candidates for bone defect and fracture repair, thanks to their suitable biodegradation rates and acceptable biocompatibility. However, the mechanical properties of AM zinc alloys developed so far, ductility in particular, fall short of the requirements for bone substitution. Here, we present Zn-1Mn and Zn-1Mn-0.4Mg alloy implants with unique microstructures, fabricated using laser powder bed fusion (LPBF). Notably, the LPBF Zn-Mn-Mg alloy exhibited an extraordinary balance of strength and ductility, with an ultimate tensile strength of 289 MPa, yield strength of 213.5 MPa, and elongation over 20 %, outperforming all previously reported AM zinc alloys. The simultaneously enhanced strength and ductility of the ternary alloy were attributed to the strong grain-refining effect of the Mg2Zn11 second phase and the synthetic strengthening caused by the dispersion of the MnZn13 and Mg2Zn11 second phases inside the grains and at the grain boundaries. In addition, both alloys had similar rates of in vitro biodegradation (∼0.15 mm/year), properly aligned with the bone remodeling process, while also demonstrating favorable biocompatibility and upregulating multiple osteogenic markers. The Zn-Mn-Mg alloy showed even better osteogenic potential than the Zn-Mn alloy, owing to the addition of Mg. The combined attributes of the LPBF Zn-Mn-Mg ternary alloy indicated huge potential for its use as a bone repair material, especially for load-bearing bone fixation. STATEMENT OF SIGNIFICANCE: The mechanical properties of previously developed additively manufactured biodegradable zinc alloys, especially ductility, have not met the requirements for bone repair. Using laser powder bed fusion (LPBF), we fabricated Zn-1Mn and Zn-1Mn-0.4Mg alloy implants with unique microstructures. The LPBF Zn-Mn-Mg alloy demonstrated an exceptional balance of strength and ductility, achieving a tensile strength of 289 MPa, yield strength of 213.5 MPa, and elongation over 20 %, surpassing all reported AM zinc alloys. This study is the first to produce a directly printed biodegradable alloy meeting the mechanical requirements for bone fixation devices without post-processing. Additionally, the alloy exhibited moderate a biodegradation rate and excellent biocompatibility, underscoring its potential for load-bearing bone repair applications.
Schlagwörter
MeSH-Schlagwörter (MEDLINE)
Stichwörter der Autor:innen
Substanzen
Autor:innen und Institutionen
- Beijing Advanced Innovation Center for Materials Genome Engineering, School of Materials Science and Engineering, University of Science and Technology Beijing, 30 Xueyuan Road, Haidian District, Beijing 100083, China; I…
- Beijing Advanced Innovation Center for Materials Genome Engineering, School of Materials Science and Engineering, University of Science and Technology Beijing, 30 Xueyuan Road, Haidian District, Beijing 100083, China.
- Department of Orthopaedics, Peking University Third Hospital, No. 49 North Garden Road, Haidian District, Beijing 100191, China.
- Department of Biomechanical Engineering, Delft University of Technology, Delft 2628 CD, the Netherlands.
- National Engineering Research Center for Advanced Rolling and Intelligent Manufacturing, Institute of Engineering Technology, University of Science and Technology Beijing, 30 Xueyuan Road, Haidian District, Beijing 1000…
Förderung
- National Key Research and Development Program of China
- Beijing Natural Science Foundation
- Beijing Nova Program
- National Natural Science Foundation of China
Zitieren
APA
Huang, C., Wang, Y., Yang, F., Shi, Y., Zhao, S., Li, X., Lu, Y., Wu, Y., Zhou, J., Zadpoor, A. A., Xu, W., Li, Y., & Wang, L. (2025). Additively manufactured biodegradable Zn-Mn-based implants with an unprecedented balance of strength and ductility. Acta Biomaterialia, 196, 506-522. https://doi.org/10.1016/j.actbio.2025.02.047
Vancouver
Huang C, Wang Y, Yang F, Shi Y, Zhao S, Li X, et al. Additively manufactured biodegradable Zn-Mn-based implants with an unprecedented balance of strength and ductility. Acta Biomaterialia. 2025;196:506-522. doi:10.1016/j.actbio.2025.02.047
BibTeX
@article{Huang2025,
author = {Huang, Chengcong and Wang, Yizhu and Yang, Fan and Shi, Yixuan and Zhao, Shangyan and Li, Xuan and Lu, Yuchen and Wu, Yuzhi and Zhou, Jie and Zadpoor, Amir A and Xu, Wei and Li, Yageng and Wang, Luning},
title = {Additively manufactured biodegradable Zn-Mn-based implants with an unprecedented balance of strength and ductility},
journal = {Acta Biomaterialia},
year = {2025},
volume = {196},
pages = {506--522},
doi = {10.1016/j.actbio.2025.02.047}
}
EUVIMED