EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Mechanical properties, degradation action, and biocompatibility of in situ nanoparticle-reinforced MgxZny/Zn composite prepared via roll bonding

Jianguo Lin, Yingzhong Chen, Yilong Dai, Xiaokai Zhang, Dechuang Zhang, Yuncang Li, Cuie Wen

Acta Biomaterialia · 2025

DOI: 10.1016/j.actbio.2025.01.048 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Acta Biomaterialia, 2025. Verfasst von Jianguo Lin und 6 weiteren Autor:innen. Beteiligte Einrichtung: School of Materials Science and Engineering, Xiangtan University, Xiangtan 411105, China. Hauptthemen laut MEDLINE: Zinc, Materials Testing, Magnesium, Biocompatible Materials. Die Arbeit wurde bisher 56-mal zitiert (Crossref) und nennt 82 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Australian Research Council, National Natural Science Foundation of China.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Zinc (Zn)-based alloys and composites are anticipated to emerge as a category of degradable metallic biomaterials with exceptional prospects for bone-implant applications owing to their superior biocompatibility and biofunctionality. Unfortunately, the limited strength of Zn alloys in their as-cast state restricts their use in clinical applications. In this study, we started with pure magnesium (Mg) powders and Zn sheets, and successfully fabricated MgxZny/Zn composites using accumulative roll bonding (ARB). The influence of varying ARB cycle numbers on their microstructures, performance in relation to mechanical parameters, corrosion resistance, and cytotoxicity was comprehensively studied. Following 15 ARB cycles, the composites demonstrated a refined Zn matrix phase with grains of 0.3 μm and uniformly distributed in situ nanoparticle reinforcements of Mg2Zn11 and MgZn2. The composites after 15 ARB cycles exhibited an ultimate tensile strength of 560 MPa, yield strength of 540 MPa, and elongation of 12 %, significantly better than the mechanical properties of most Zn alloys reported to date. The significant improvement in the composites' strength is primarily attributable to refinement of grain size and dispersion strengthening, both of which are facilitated by the in situ incorporation of nanoparticles. The corrosion rate reduced with more ARB cycles and after 15 ARB cycles the composites had an electrochemical corrosion rate of 150.2 μm/y and an immersion degradation rate of 50.6 μm/y. Further, an extract at 12.5 % concentration had a cell viability of 92.2 % toward MG-63 cells, indicating good biocompatibility. STATEMENT OF SIGNIFICANCE: This work reports on MgxZny/Zn composites fabricated by accumulative roll bonding (ARB). The composite after 15 ARB cycles exhibited an ultimate tensile strength of 560 MPa, yield strength of 540 MPa, and elongation of 12 %, significantly higher than the mechanical properties of most Zn alloys published in the literature to date. The corrosion rate of the composites decreased with increasing number of ARB cycles and after 15 ARB cycles they showed an electrochemical corrosion rate of 150.2 μm/y and immersion degradation rate of 50.6 μm/y. Further, a 12.5 % concentration extract showed a cell viability of 92.2 % in relation to MG-63 cells, indicating good biocompatibility.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

ZincMaterials TestingMagnesiumBiocompatible MaterialsNanoparticlesHumansTensile StrengthCorrosionAlloysCell Survival

Stichwörter der Autor:innen

Accumulative roll bondingCytotoxicityDegradation rateMg(x)Zn(y)/Zn compositeStrengthening mechanism

Substanzen

ZincMagnesiumBiocompatible MaterialsAlloys

Autor:innen und Institutionen

  • School of Materials Science and Engineering, Xiangtan University, Xiangtan 411105, China.
  • School of Materials Science and Engineering, Xiangtan University, Xiangtan 411105, China. Electronic address: daiyilong@xtu.edu.cn.
  • Key Laboratory of Low Dimensional Materials and Application Technology, Ministry of Education, Xiangtan University, Xiangtan, 411105, China; APT Medical Inc., Xiangtan 411105, China.
  • Key Laboratory of Low Dimensional Materials and Application Technology, Ministry of Education, Xiangtan University, Xiangtan, 411105, China. Electronic address: dczhang@xtu.edu.cn.
  • Centre for Additive Manufacturing, School of Engineering, RMIT University, Melbourne, Victoria 3001, Australia.
  • Centre for Additive Manufacturing, School of Engineering, RMIT University, Melbourne, Victoria 3001, Australia. Electronic address: cuie.wen@rmit.edu.au.

Förderung

  • Australian Research Council
  • National Natural Science Foundation of China

Zitieren

APA

Lin, J., Chen, Y., Dai, Y., Zhang, X., Zhang, D., Li, Y., & Wen, C. (2025). Mechanical properties, degradation action, and biocompatibility of in situ nanoparticle-reinforced MgxZny/Zn composite prepared via roll bonding. Acta Biomaterialia. https://doi.org/10.1016/j.actbio.2025.01.048

Vancouver

Lin J, Chen Y, Dai Y, Zhang X, Zhang D, Li Y, et al. Mechanical properties, degradation action, and biocompatibility of in situ nanoparticle-reinforced MgxZny/Zn composite prepared via roll bonding. Acta Biomaterialia. 2025. doi:10.1016/j.actbio.2025.01.048

BibTeX
@article{Lin2025,
  author = {Lin, Jianguo and Chen, Yingzhong and Dai, Yilong and Zhang, Xiaokai and Zhang, Dechuang and Li, Yuncang and Wen, Cuie},
  title = {Mechanical properties, degradation action, and biocompatibility of in situ nanoparticle-reinforced MgxZny/Zn composite prepared via roll bonding},
  journal = {Acta Biomaterialia},
  year = {2025},
  doi = {10.1016/j.actbio.2025.01.048}
}
Kostenlos starten →