EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Interconnectable 3D-printed sample processing modules for portable mycotoxin screening of intact wheat

Anouk J Bosman, Stephan Freitag, Georgina M S Ross, Michael Sulyok, Rudolf Krska, Francesco Simone Ruggeri, Gert Ij Salentijn

Analytica Chimica Acta · 2024-01 · 1285 · 342000

DOI: 10.1016/j.aca.2023.342000 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Analytica Chimica Acta, 2024-01. Verfasst von Anouk J Bosman und 6 weiteren Autor:innen. Beteiligte Einrichtung: Laboratory of Organic Chemistry, Wageningen University & Research, Stippeneng 4, 6708 WE, Wageningen, the Netherlands; Wageningen Food Safety Researc…. Hauptthemen laut MEDLINE: Mycotoxins. Die Arbeit wurde bisher 9-mal zitiert (Crossref) und nennt 52 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Horizon 2020, Emory University, European Union.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

BACKGROUND: The increasing demand for food and feed products is stretching the capacity of the food value chain to its limits. A key step for ensuring food safety is checking for mycotoxin contamination of wheat. However, this analysis is typically performed by rather complex and expensive chromatographic methods, such as liquid chromatography-tandem mass spectrometry (LC-MS/MS). These costly methods require extensive sample preparation that is not easily carried out at different points along the food supply chain. To overcome such challenges in sample processing, an inexpensive and portable sample preparation device was needed, that required low skill, for rapid sample-to-result mycotoxin screening. RESULTS: We describe 3D-printed and interconnectable modules for simple, integrated and on-site sample preparation, including grinding of wheat kernels, and solvent-based extraction. We characterized these 3D-printed modules for mycotoxin screening and benchmarked them against a laboratory mill using commercial lateral flow device(s) (LFD) and in-house validated LC-MS/MS analysis. Different integrated sieve configurations were compared based on grinding efficiency, and we selected a sieve size of 2 mm allowing grinding of 10 g of wheat within 5 min. Moreover, 10 first time-users were able to operate the grinder module with minimal instructions. Screening for deoxynivalenol (DON) in naturally contaminated samples at the regulatory/legal limit (1.25 mg kg-1) was demonstrated using the developed 3D-printed prototype. The whole process only takes 15 min, from sample preparation to screening result. The results showed a clear correlation (R2 = 0.96) between the LFD and LC-MS/MS. SIGNIFICANCE: Our findings demonstrate the potential of 3D-printed sample handling equipment as a valuable extension of existing analytical procedures, facilitating the on-site implementation of rapid methods for the determination of mycotoxins in grains. The presented prototype is inexpensive with material costs of 2.5€, relies on biodegradable 3D printing filament and can be produced with consumer-grade printers, making the prototype readily available. As a future perspective, the modular character of our developed tool kit will allow for adaptation to other hard food commodities beyond the determination of DON in wheat.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

MycotoxinsChromatography, LiquidTriticumTandem Mass SpectrometryFood Contamination

Stichwörter der Autor:innen

3D printingLC-MS/MSLateral flow devicesMycotoxin screeningPortableSample preparation

Substanzen

Mycotoxins

Autor:innen und Institutionen

  • Laboratory of Organic Chemistry, Wageningen University & Research, Stippeneng 4, 6708 WE, Wageningen, the Netherlands; Wageningen Food Safety Research, Wageningen University & Research, Akkermaalsbos 2, 6708 WB, Wagenin…
  • University of Natural Resources and Life Sciences, Vienna, Department of Agrobiotechnology, IFA-Tulln, Institute of Bioanalytics and Agro-Metabolomics, Konrad-Lorenz-Strasse 20, 3430 Tulln an der Donau, Austria.
  • University of Natural Resources and Life Sciences, Vienna, Department of Agrobiotechnology, IFA-Tulln, Institute of Bioanalytics and Agro-Metabolomics, Konrad-Lorenz-Strasse 20, 3430 Tulln an der Donau, Austria; Institu…
  • Laboratory of Organic Chemistry, Wageningen University & Research, Stippeneng 4, 6708 WE, Wageningen, the Netherlands; Physical Chemistry and Soft Matter, Wageningen University & Research, Stippeneng 4, 6708 WE, Wagenin…

Förderung

  • Horizon 2020
  • Emory University
  • European Union

Zitieren

APA

Bosman, A. J., Freitag, S., Ross, G. M. S., Sulyok, M., Krska, R., Ruggeri, F. S., & Salentijn, G. I. (2024). Interconnectable 3D-printed sample processing modules for portable mycotoxin screening of intact wheat. Analytica Chimica Acta, 1285, 342000. https://doi.org/10.1016/j.aca.2023.342000

Vancouver

Bosman AJ, Freitag S, Ross GMS, Sulyok M, Krska R, Ruggeri FS, et al. Interconnectable 3D-printed sample processing modules for portable mycotoxin screening of intact wheat. Analytica Chimica Acta. 2024;1285:342000. doi:10.1016/j.aca.2023.342000

BibTeX
@article{Bosman2024,
  author = {Bosman, Anouk J and Freitag, Stephan and Ross, Georgina M S and Sulyok, Michael and Krska, Rudolf and Ruggeri, Francesco Simone and Salentijn, Gert Ij},
  title = {Interconnectable 3D-printed sample processing modules for portable mycotoxin screening of intact wheat},
  journal = {Analytica Chimica Acta},
  year = {2024},
  volume = {1285},
  pages = {342000},
  doi = {10.1016/j.aca.2023.342000}
}
Kostenlos starten →