EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Effect of olive-pruning fibres as reinforcements of alkali-activated cements based on electric arc furnace slag and biomass bottom ash

M. A. Gómez-Casero, P. J. Sánchez-Soto, E. Castro, D. Eliche-Quesada

Archives of Civil and Mechanical Engineering · 18.03.2024 · 24 (2)

DOI: 10.1007/s43452-024-00882-0 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Archives of Civil and Mechanical Engineering, online erschienen am 18.03.2024. Verfasst von M. A. Gómez-Casero und 3 weiteren Autor:innen. Die Arbeit wurde bisher 8-mal zitiert (Crossref) und nennt 84 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Ministerio de Ciencia, Innovación y Universidades, Ministerio de Ciencia e Innovación, Universidad de Jaén.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

In this work, alkali-activated composites using electric arc furnace slag (50 wt%) and biomass bottom ash (50 wt%) were manufactured, adding olive-pruning fibres as reinforcement. The objective of adding fibres is to improve the flexural strength of composites, as well as to prevent the expansion of cracks as a result of shrinkage. For this reason, composites reinforced with olive-pruning fibres (0.5–2 wt%) untreated and treated with three different solutions to improve matrix–fibre adhesion were manufactured. Treatments developed over fibres were a 10 wt% Na 2 SiO 3 solution, 3 wt% CaCl 2 solution and 5 wt% NaOH solution. Mechanical properties, physical properties, thermal properties and the microstructure of composites by Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD) and scanning electron microscopy (SEM) were studied to demonstrate the improvement. Alkaline treatment degraded fibre surface, increasing the matrix–fibre adhesion, and as a consequence, flexural strength increased up to 20% at 90 days of curing. Optimal results were obtained with composites reinforced with 1 wt% of olive-pruning fibre treated by a 10 wt% Na 2 SiO 3 solution. Higher quantity of olive-pruning fibre leads to local agglomeration, which weakens the matrix–fibre adhesion. The effect on the compressive strength is less evident, since the addition of fibres produces an admissible decrease (between 0 and 9% using 0.5 or 1 wt% of fibres), except in composites that use olive pruning treated with 10 wt% Na 2 SiO 3 solution, where values remain stable, similar or better to control paste. A greater ductility of the matrix in all composites was observed. Furthermore, the alkali-activated cement matrix was bonded to olive-pruning fibre better than untreated fibre, as it is shown in SEM images. Thus, the results showed that olive-pruning fibres could be used as reinforcement in the manufacturing of alkali-activated materials when they are treated with alkali solutions.

Förderung

  • Ministerio de Ciencia, Innovación y Universidades
  • Ministerio de Ciencia e Innovación
  • Universidad de Jaén

Zitieren

APA

Gómez-Casero, M. A., Sánchez-Soto, P. J., Castro, E., & Eliche-Quesada, D. (2024). Effect of olive-pruning fibres as reinforcements of alkali-activated cements based on electric arc furnace slag and biomass bottom ash. Archives of Civil and Mechanical Engineering, 24(2). https://doi.org/10.1007/s43452-024-00882-0

Vancouver

Gómez-Casero MA, Sánchez-Soto PJ, Castro E, Eliche-Quesada D. Effect of olive-pruning fibres as reinforcements of alkali-activated cements based on electric arc furnace slag and biomass bottom ash. Archives of Civil and Mechanical Engineering. 2024;24(2). doi:10.1007/s43452-024-00882-0

BibTeX
@article{GmezCasero2024,
  author = {Gómez-Casero, M. A. and Sánchez-Soto, P. J. and Castro, E. and Eliche-Quesada, D.},
  title = {Effect of olive-pruning fibres as reinforcements of alkali-activated cements based on electric arc furnace slag and biomass bottom ash},
  journal = {Archives of Civil and Mechanical Engineering},
  year = {2024},
  volume = {24},
  number = {2},
  doi = {10.1007/s43452-024-00882-0}
}
Kostenlos starten →