Construct–construct “rail technique” decreases screw strain during spinal deformity corrective maneuvers across a thoracic vertebral column resection: a cadaveric analysis
Spine Deformity · 2026
DOI: 10.1007/s43390-025-01195-9 ↗Kurz gefasst
Fachartikel in der Zeitschrift Spine Deformity, 2026. Verfasst von Alekos A Theologis und 4 weiteren Autor:innen. Beteiligte Einrichtung: Department of Orthopaedic Surgery, University of California - San Francisco (UCSF), 500 Parnassus Ave, MUW 3Rd Floor, San Francisco, CA, 94143, USA. …. Hauptthemen laut MEDLINE: Thoracic Vertebrae, Pedicle Screws, Kyphosis, Spinal Fusion. Die Arbeit nennt 27 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Globus Medical Inc..
Abstract (Originalsprache)
Purpose
To biomechanically compare screw strains above and below a vertebral column resection (VCR) during segmental compression (SC) and cantilever bending (CB) performed via traditional methods and a novel, construct-to-construct accessory rod (“rail”) technique.
Methods
Eight cadaveric torsos underwent a VCR with 25 0 kyphosis at T8 with pedicle screws implanted three levels above and below the VCR (T5-7; T9-11). Four screws (T6, T7, T9, T10) were instrumented with strain gauges to capture screw strains during SC and CB. Both deformity corrective maneuvers were performed over a traditional construct (central rod) and over a construct-to-construct accessory (“rail”) rod. Real-time screw strains were collected and peak strains were compared between corrective techniques.
Results
Strains in screws closest to the VCR were significantly less during “rail” compression compared to traditional SC (T7: p = 0.015). Maximum screw strains were significantly lower during “rail” SC and CB compared to traditional SC (T6: p = 0.037; T7: p = 0.015) and CB (T6: p = 0.018; T9: p < 0.001). Total screw strain was more evenly distributed over all screws during “rail” compression and CB compared to traditional techniques, which concentrated strain at individual screws adjacent to the VCR.
Conclusions
Performing segmental compression and cantilever bending across a lateral accessory construct-to-construct (“rail”) rod resulted in significantly lower strain on individual pedicle screws adjacent to a thoracic VCR compared to traditional SC and CB. As such, the “rail” may lessen risk of screw pull-out and screw plough during maneuvers to correct spinal deformities across a VCR.
Schlagwörter
MeSH-Schlagwörter (MEDLINE)
Stichwörter der Autor:innen
Autor:innen und Institutionen
- Department of Orthopaedic Surgery, University of California - San Francisco (UCSF), 500 Parnassus Ave, MUW 3Rd Floor, San Francisco, CA, 94143, USA. alekos.theologis@ucsf.edu.
- Scientific Affairs, Globus Medical Inc, Audubon, PA, USA.
ORCID-Profile: Alekos A Theologis
Förderung
- Globus Medical Inc.
Zitieren
APA
Theologis, A. A., DePhillips, J., Lachcik, I. T., Mahoney, J. M., & Bucklen, B. S. (2026). Construct–construct “rail technique” decreases screw strain during spinal deformity corrective maneuvers across a thoracic vertebral column resection: a cadaveric analysis. Spine Deformity. https://doi.org/10.1007/s43390-025-01195-9
Vancouver
Theologis AA, DePhillips J, Lachcik IT, Mahoney JM, Bucklen BS. Construct–construct “rail technique” decreases screw strain during spinal deformity corrective maneuvers across a thoracic vertebral column resection: a cadaveric analysis. Spine Deformity. 2026. doi:10.1007/s43390-025-01195-9
BibTeX
@article{Theologis2026,
author = {Theologis, Alekos A and DePhillips, Jason and Lachcik, Izabella T and Mahoney, Jonathan M and Bucklen, Brandon S},
title = {Construct–construct “rail technique” decreases screw strain during spinal deformity corrective maneuvers across a thoracic vertebral column resection: a cadaveric analysis},
journal = {Spine Deformity},
year = {2026},
doi = {10.1007/s43390-025-01195-9}
}
EUVIMED