Plasma treatment of dental zirconia produced by nano particle jetting additive manufacturing and conventional milling
Journal of the Australian Ceramic Society · 2026-03 · 62 (1) · 19-32
DOI: 10.1007/s41779-025-01229-5 ↗Kurz gefasst
Fachartikel in der Zeitschrift Journal of the Australian Ceramic Society, online erschienen am 17.07.2025. Verfasst von Bengi Yilmaz Erdemli und 5 weiteren Autor:innen. Die Arbeit wurde bisher 4-mal zitiert (Crossref) und nennt 64 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: ITI Foundation, University of Health Sciences.
Abstract (Originalsprache)
This study investigates the surface properties of zirconia fabricated via nano particle jetting (NPJ), a material jetting–based additive manufacturing (AM) technique, and compares them to conventionally milled (CM) zirconia following plasma surface treatment. AM zirconia discs were produced using a 3 mol% yttria-stabilized ZrO₂ slurry, while CM discs were prepared from semi-sintered blocks. Both sample types were sintered at 1500 °C, ground, and subjected to low-pressure, low-temperature air plasma treatment for 1 or 5 min. Initial grain sizes were 0.545 ± 0.211 μm for AM and 0.520 ± 0.214 μm for CM zirconia, and X-ray diffraction confirmed the preservation of the tetragonal phase after treatment. Surface roughness parameters remained within the nanometer range and were unaffected by plasma exposure. As-built water contact angles were 59.1° ± 8.6° for AM and 58.9° ± 9.0° for CM zirconia, indicating comparable inherent hydrophilicity. Plasma treatment effectively reduced carbon residues and enhanced surface wettability by lowering the contact angles to 14.5° ± 3.1° (AM) and 15.7° ± 2.2° (CM) after 1-min treatment. However, no significant differences were observed with longer treatment durations. The effect was sustained for at least 72 h in closed storage but reverted after 2 months in ambient conditions. Vickers hardness of AM zirconia was 1298 ± 13 HV1.0, which was lower than that of CM zirconia (1341 ± 8 HV1.0) and plasma treatment had no measurable effect on surface hardness. This is the first study to systematically compare NPJ-manufactured and milled zirconia under standardized plasma conditions. The findings demonstrate the feasibility of NPJ zirconia for dental applications and the potential of plasma surface modification to improve early-stage biological responses through enhanced wettability. Graphical abstract
Förderung
- ITI Foundation
- University of Health Sciences
Zitieren
APA
Erdemli, B. Y., Kalyoncuoğlu, Ü. T., Ayyıldız, S., Tahmasebifar, A., Baran, E. T., & Akça, G. (2026). Plasma treatment of dental zirconia produced by nano particle jetting additive manufacturing and conventional milling. Journal of the Australian Ceramic Society, 62(1), 19-32. https://doi.org/10.1007/s41779-025-01229-5
Vancouver
Erdemli BY, Kalyoncuoğlu ÜT, Ayyıldız S, Tahmasebifar A, Baran ET, Akça G. Plasma treatment of dental zirconia produced by nano particle jetting additive manufacturing and conventional milling. Journal of the Australian Ceramic Society. 2026;62(1):19-32. doi:10.1007/s41779-025-01229-5
BibTeX
@article{Erdemli2026,
author = {Erdemli, Bengi Yilmaz and Kalyoncuoğlu, Ülkü Tuğba and Ayyıldız, Simel and Tahmasebifar, Aydin and Baran, Erkan Türker and Akça, Gülçin},
title = {Plasma treatment of dental zirconia produced by nano particle jetting additive manufacturing and conventional milling},
journal = {Journal of the Australian Ceramic Society},
year = {2026},
volume = {62},
number = {1},
pages = {19--32},
doi = {10.1007/s41779-025-01229-5}
}
EUVIMED