Additive manufacturing of carbon-martensitic hardening ledeburitic cold work tool steels using Fused Filament Fabrication and subsequent Supersolidus Liquid-Phase Sintering
Progress in Additive Manufacturing · 2025-01 · 10 (1) · 679-700
DOI: 10.1007/s40964-024-00650-9 ↗Kurz gefasst
Fachartikel in der Zeitschrift Progress in Additive Manufacturing, online erschienen am 14.05.2024. Verfasst von A. Röttger und 5 weiteren Autor:innen. Die Arbeit wurde bisher 7-mal zitiert (Crossref) und nennt 69 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Bundesministerium für Wirtschaft und Klimaschutz, Bergische Universität Wuppertal.
Abstract (Originalsprache)
In this work, the microstructure property relationship of D2 (X153CrMoV12; 1.2379) ledeburitic cold work steel processed by filament extrusion is investigated. Contrary to the conventional process, which involves a multi-step process of printing, debinding, and solid-state sintering, the specimens in this study were densified using Supersolidus Liquid-Phase Sintering (SLPS). SLPS occurs after thermal debinding in the interval between the solidus and liquidus temperatures. Optimized liquid-phase volume fraction was evaluated by means of thermodynamic calculations using the CALPHAD method and their experimental validation. The microstructure formation process during debinding, solid state, and SLPS sintering was investigated by X-ray diffraction and electron microscopy. Tomography studies confirm a relative density of 99.92% by volume during SLPS sintering at 1280 °C and provide a deep insight into local densification behavior during SLPS processing. In addition, surface roughness, as determined by confocal laser scanning microscopy, could be reduced. The reduction in porosity and surface roughness can be attributed to the presence of a liquid phase during SLPS. Using adapted heat treatment parameters determined by hardness-tempering curves, higher hardness values were achieved for SLPS-post-compacted specimens compared to conventionally processed specimens and the same material in the cast and heat-treated reference state.
Förderung
- Bundesministerium für Wirtschaft und Klimaschutz
- Bergische Universität Wuppertal
Zitieren
APA
Röttger, A., Wieczorek, L., Schmidtseifer, N., Katzwinkel, T., Blüm, M., & Löwer, M. (2025). Additive manufacturing of carbon-martensitic hardening ledeburitic cold work tool steels using Fused Filament Fabrication and subsequent Supersolidus Liquid-Phase Sintering. Progress in Additive Manufacturing, 10(1), 679-700. https://doi.org/10.1007/s40964-024-00650-9
Vancouver
Röttger A, Wieczorek L, Schmidtseifer N, Katzwinkel T, Blüm M, Löwer M. Additive manufacturing of carbon-martensitic hardening ledeburitic cold work tool steels using Fused Filament Fabrication and subsequent Supersolidus Liquid-Phase Sintering. Progress in Additive Manufacturing. 2025;10(1):679-700. doi:10.1007/s40964-024-00650-9
BibTeX
@article{Rttger2025,
author = {Röttger, A. and Wieczorek, L. and Schmidtseifer, N. and Katzwinkel, T. and Blüm, M. and Löwer, M.},
title = {Additive manufacturing of carbon-martensitic hardening ledeburitic cold work tool steels using Fused Filament Fabrication and subsequent Supersolidus Liquid-Phase Sintering},
journal = {Progress in Additive Manufacturing},
year = {2025},
volume = {10},
number = {1},
pages = {679--700},
doi = {10.1007/s40964-024-00650-9}
}
EUVIMED