EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

FPGA-Based LQG Control of a Low-Speed Active Magnetic Bearing Joint: Implementation and Validation

Walter Torrestiana González, Leopoldo González González, Emmanuel González Mendoza, Luis Bautista Cruz

Journal of Control, Automation and Electrical Systems · 2026-10 · 37 (5) · 1091-1103

DOI: 10.1007/s40313-026-01286-6 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Journal of Control, Automation and Electrical Systems, online erschienen am 05.05.2026. Verfasst von Walter Torrestiana González und 3 weiteren Autor:innen. Die Arbeit wurde bisher 1-mal zitiert (Crossref) und nennt 28 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Dirección General de Asuntos del Personal Académico, Universidad Nacional Autónoma de México.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Active magnetic bearings (AMBs) enable contactless support and are attractive for precision mechanisms in particle-sensitive environments. This work presents a complete discrete-time linear–quadratic–Gaussian (LQG) control pipeline on a field-programmable gate array (FPGA) for a low-speed robotic joint using a three-degree-of-freedom active magnetic bearing (two radial axes and one axial levitator). A translational physics-based model explicitly captures bias currents and nominal air gaps, followed by equilibrium linearization and zero-order-hold discretization at 2 kHz. The estimator–controller ( linear–quadratic regulator , LQR, plus Kalman filter) is implemented in fixed-point logic with sub-200 $$\upmu $$ μ s end-to-end latency. Experiments on a dedicated testbed compare the proposed LQG against a tuned proportional–integral–derivative (PID) controller and an observer-based pole-placement baseline under identical sensing and actuation. In the radial loop, LQG reduces startup settling time by approximately 44% and integrated absolute error by approximately 36.5%, with overshoot below 0.5% and actuator limits respected; recovery to a $$\pm 5\%$$ ± 5 % band under external disturbances is about 13% faster. A nonlinear plant robustness map indicates stable, non-overshooting behavior under $$\pm 20\%$$ ± 20 % variations of magnetic and electrical parameters. Particle measurements during continuous operation remain below the International Organization for Standardization (ISO) Class 5 thresholds, supporting the suitability of the proposed joint for cleanroom robotics.

Förderung

  • Dirección General de Asuntos del Personal Académico, Universidad Nacional Autónoma de México

Zitieren

APA

González, W. T., González, L. G., Mendoza, E. G., & Cruz, L. B. (2026). FPGA-Based LQG Control of a Low-Speed Active Magnetic Bearing Joint: Implementation and Validation. Journal of Control, Automation and Electrical Systems, 37(5), 1091-1103. https://doi.org/10.1007/s40313-026-01286-6

Vancouver

González WT, González LG, Mendoza EG, Cruz LB. FPGA-Based LQG Control of a Low-Speed Active Magnetic Bearing Joint: Implementation and Validation. Journal of Control, Automation and Electrical Systems. 2026;37(5):1091-1103. doi:10.1007/s40313-026-01286-6

BibTeX
@article{Gonzlez2026,
  author = {González, Walter Torrestiana and González, Leopoldo González and Mendoza, Emmanuel González and Cruz, Luis Bautista},
  title = {FPGA-Based LQG Control of a Low-Speed Active Magnetic Bearing Joint: Implementation and Validation},
  journal = {Journal of Control, Automation and Electrical Systems},
  year = {2026},
  volume = {37},
  number = {5},
  pages = {1091--1103},
  doi = {10.1007/s40313-026-01286-6}
}
Kostenlos starten →