EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Aerosol Deposition of CuFeO2 Photocathode Coatings for Hydrogen Production

Alessia Bruera, Andreas Elsenberg, Mauro Borghi, Giulia Dolcetti, Giovanni Bolelli, Frank Gärtner, Mauricio Schieda, Thomas Klassen, Luca Lusvarghi

Journal of Thermal Spray Technology · 2024-08 · 33 (6) · 1746-1770

DOI: 10.1007/s11666-024-01798-0 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Journal of Thermal Spray Technology, online erschienen am 02.07.2024. Verfasst von Alessia Bruera und 8 weiteren Autor:innen. Die Arbeit wurde bisher 10-mal zitiert (Crossref) und nennt 58 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Università degli Studi di Modena e Reggio Emilia.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Photoelectrochemical (PEC) water splitting is a viable route for green hydrogen generation. In PEC cells, the electrodes are coated with suitable semiconductor materials, which absorb the sunlight, generating charge carriers that are used to split water molecules into H 2 and O 2 . CuFeO 2 is one promising photocathode material for water splitting. However, its performance is limited by electron/hole pairs recombination within the film and at the film/substrate interface. Aerosol deposition (AD) can be employed to minimize charge recombination by spraying dense, thin films and by establishing a good back-contact interface. In this study, CuFeO 2 powders were synthesized through a conventional solid-state technique and sprayed by AD under varied parameter sets. The effect of particle size distributions, carrier gas, gas pressure and substrate temperature was investigated. The best spraying parameter set was then tuned to obtain thin coatings (< 1 µm). Single-particle deformation and coatings microstructure were investigated by scanning electron microscopy. Optical properties of CuFeO 2 films were analyzed by UV–Vis spectroscopy, while photoelectrochemical performances were estimated through amperometry tests under simulated sunlight. The results of this research show that CuFeO 2 photocathodes can be successfully manufactured by AD. Their performance can be optimized by adjusting coating thickness and by annealing in air.

Förderung

  • Università degli Studi di Modena e Reggio Emilia

Zitieren

APA

Bruera, A., Elsenberg, A., Borghi, M., Dolcetti, G., Bolelli, G., Gärtner, F., Schieda, M., Klassen, T., & Lusvarghi, L. (2024). Aerosol Deposition of CuFeO2 Photocathode Coatings for Hydrogen Production. Journal of Thermal Spray Technology, 33(6), 1746-1770. https://doi.org/10.1007/s11666-024-01798-0

Vancouver

Bruera A, Elsenberg A, Borghi M, Dolcetti G, Bolelli G, Gärtner F, et al. Aerosol Deposition of CuFeO2 Photocathode Coatings for Hydrogen Production. Journal of Thermal Spray Technology. 2024;33(6):1746-1770. doi:10.1007/s11666-024-01798-0

BibTeX
@article{Bruera2024,
  author = {Bruera, Alessia and Elsenberg, Andreas and Borghi, Mauro and Dolcetti, Giulia and Bolelli, Giovanni and Gärtner, Frank and Schieda, Mauricio and Klassen, Thomas and Lusvarghi, Luca},
  title = {Aerosol Deposition of CuFeO2 Photocathode Coatings for Hydrogen Production},
  journal = {Journal of Thermal Spray Technology},
  year = {2024},
  volume = {33},
  number = {6},
  pages = {1746--1770},
  doi = {10.1007/s11666-024-01798-0}
}
Kostenlos starten →