EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

An Experimental Method for Fatigue Testing Cast Iron Water Pipes Using Combined Internal Water Pressure and Bending Loads

E D A John, J B Boxall, R P Collins, E T Bowman, L Susmel iD

Experimental Mechanics · 2025-06 · 65 (5) · 605-623

DOI: 10.1007/s11340-025-01153-6 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Experimental Mechanics, online erschienen am 10.02.2025. Verfasst von E D A John und 4 weiteren Autor:innen. Beteiligte Einrichtung: School of Mechanical, Aerospace and Civil Engineering, Sir Frederick Mappin Building, The University of Sheffield, Mappin Street, Sheffield, S1 4DT U…. Die Arbeit wurde bisher 4-mal zitiert (Crossref) und nennt 37 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Engineering and Physical Sciences Research Council.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Background

Investigations into the fatigue failures mechanism of Grey Cast Iron (GCI) water pipes are inhibited by the lack of a lab-based method to conduct extensive high-cycle biaxial fatigue test programmes.

Objective

The work presented in this paper developed and tested a novel experiment capable of causing controlled fatigue failures of GCI pipe specimens in the high-cycle fatigue regime using bending and internal water pressure fatigue loading.

Methods

A novel four-point bending and internal water pressure fatigue testing system was developed to apply constant amplitude out-of-phase biaxial loading to 58 mm diameter GCI pipes at 1.7 Hz. To verify the ability of this equipment to apply known stresses and repeatable loads to pipe specimens a series of tests were conducted. A finite element model of the pipe specimen was used to estimate the strains and displacements applied by the equipment.

Results

Experimental strains and displacements were mainly within ± 10% of the estimated values and the pressure amplitudes measured over 10 3 cycles were within ± 3% of the average. Dynamic load effects occurred at higher bending loads, but these were quantified and accounted for. Trial destructive tests revealed that the lifespan of leaking fatigue cracks in GCI pipes with uniform wall-loss subject to combined internal pressure and bending fatigue loads is less than 1% of the total cycles-to-burst.

Conclusions

The experimental method developed was able to apply combined, out-of-phase internal pressure and bending fatigue loads accurately and consistently to small-dimeter GCI pipes, and cause these pipes to develop high-cycle fatigue regime failures.

Schlagwörter

Stichwörter der Autor:innen

Biaxial fatigueConstant amplitudeExperiment verificationGrey cast ironWater pipe

Autor:innen und Institutionen

  • School of Mechanical, Aerospace and Civil Engineering, Sir Frederick Mappin Building, The University of Sheffield, Mappin Street, Sheffield, S1 4DT UK.
  • Materials and Engineering Research Institute, Sheffield Hallam University, Harmer Building, Sheffield, S1 1WB UK.

ORCID-Profile: L Susmel

Förderung

  • Engineering and Physical Sciences Research Council

Zitieren

APA

John, E. D. A., Boxall, J. B., Collins, R. P., Bowman, E. T., & Susmel, L. (2025). An Experimental Method for Fatigue Testing Cast Iron Water Pipes Using Combined Internal Water Pressure and Bending Loads. Experimental Mechanics, 65(5), 605-623. https://doi.org/10.1007/s11340-025-01153-6

Vancouver

John EDA, Boxall JB, Collins RP, Bowman ET, Susmel L. An Experimental Method for Fatigue Testing Cast Iron Water Pipes Using Combined Internal Water Pressure and Bending Loads. Experimental Mechanics. 2025;65(5):605-623. doi:10.1007/s11340-025-01153-6

BibTeX
@article{John2025,
  author = {John, E D A and Boxall, J B and Collins, R P and Bowman, E T and Susmel, L},
  title = {An Experimental Method for Fatigue Testing Cast Iron Water Pipes Using Combined Internal Water Pressure and Bending Loads},
  journal = {Experimental Mechanics},
  year = {2025},
  volume = {65},
  number = {5},
  pages = {605--623},
  doi = {10.1007/s11340-025-01153-6}
}
Kostenlos starten →