EUVIMEDEUVIMED entdecken
VergleichsstudieOpen Access · CC BY 4.0

Comparative Formulation and Physicochemical Evaluation of Orodispersible Films Fabricated via Pneumatic and Syringe-Based 3D Printing

Ishwor Poudel, Nur Mita, James Scherer, Manjusha Annaji, Xuejia Kang, Oladiran Fasina, Amit K Tiwari, R Jayachandra Babu

Pharmaceutical Research · 2025

DOI: 10.1007/s11095-025-03967-4 ↗

Kurz gefasst

Vergleichsstudie in der Zeitschrift Pharmaceutical Research, 2025. Verfasst von Ishwor Poudel und 7 weiteren Autor:innen. Beteiligte Einrichtung: Department of Drug Discovery and Development, Auburn University, Auburn, AL, 36830, USA. Hauptthemen laut MEDLINE: Printing, Three-Dimensional, Drug Compounding. Die Arbeit wurde bisher 1-mal zitiert (Crossref) und nennt 42 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Auburn University.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Objective

Orodispersible films (ODF) blend the dose accuracy of solid dosage forms and the ease of administration of liquid dosage forms, hence offer many advantages. This study investigated the feasibility of two extrusion-based 3D printing techniques (pneumatic and syringe) to fabricate ODFs in a benchtop setting.

Methods

We fabricated fast-dissolving ODFs using pneumatic and syringe print heads and compared the variations in the process parameters, ease of fabrication, and characterized the properties of the final dosage forms. The variation in the printing parameters, drying time, drying temperature, and needle/nozzle types on the reproducibility and uniformity of the ODFs prepared from, these two printheads were studied. Feed materials for extrusion were selected based on rheological properties, printability, and reproducibility. An optimized ODF formulation composition was kept common and utilized for comparison.

Results

The ODFs from pneumatic and syringe-based extrusion printheads consistently created bulk batches with little to no significant variation. Syringe-based extrusion showed high precision with identical dimensions, whereas pneumatic extrusion showed quick fabrication. The ODFs produced by both methods were highly reproducible and showed excellent film properties such as mechanical strength, disintegration, and dissolution. The ODFs showed adequate mechanical strength (>0.72 N/mm 2 ) for packaging and transport. The disintegration time was less than a minute, and quicker dissolution within 20 min.

Conclusion

Both pneumatic and syringe-based 3D printing technologies are deemed to be potentially viable alternatives for the fabrication of personalized dosage forms such as ODFs in pharmacy and clinical settings.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Printing, Three-DimensionalDrug CompoundingSyringesSolubilityDrug LiberationReproducibility of ResultsAdministration, OralChemistry, PharmaceuticalRheologyDrug Delivery SystemsTechnology, Pharmaceutical

Stichwörter der Autor:innen

3D printingdisintegrantgel extrusionorodispersible filmpolymer

Autor:innen und Institutionen

  • Department of Drug Discovery and Development, Auburn University, Auburn, AL, 36830, USA.
  • Faculty of Pharmacy, Mulawarman University, Samarinda, Kalimantan Timur, 75119, Indonesia.
  • Department of Biochemistry, Auburn University, Auburn, AL, 36830, USA.
  • Department of Biosystems Engineering, Auburn University, Auburn, AL, 36830, USA.
  • College of Pharmacy, University of Arkansas for Medical Sciences, Little Rock, AR, 72205, USA.
  • Department of Drug Discovery and Development, Auburn University, Auburn, AL, 36830, USA. ramapjb@auburn.edu.

Förderung

  • Auburn University

Zitieren

APA

Poudel, I., Mita, N., Scherer, J., Annaji, M., Kang, X., Fasina, O., Tiwari, A. K., & Babu, R. J. (2025). Comparative Formulation and Physicochemical Evaluation of Orodispersible Films Fabricated via Pneumatic and Syringe-Based 3D Printing. Pharmaceutical Research. https://doi.org/10.1007/s11095-025-03967-4

Vancouver

Poudel I, Mita N, Scherer J, Annaji M, Kang X, Fasina O, et al. Comparative Formulation and Physicochemical Evaluation of Orodispersible Films Fabricated via Pneumatic and Syringe-Based 3D Printing. Pharmaceutical Research. 2025. doi:10.1007/s11095-025-03967-4

BibTeX
@article{Poudel2025,
  author = {Poudel, Ishwor and Mita, Nur and Scherer, James and Annaji, Manjusha and Kang, Xuejia and Fasina, Oladiran and Tiwari, Amit K and Babu, R Jayachandra},
  title = {Comparative Formulation and Physicochemical Evaluation of Orodispersible Films Fabricated via Pneumatic and Syringe-Based 3D Printing},
  journal = {Pharmaceutical Research},
  year = {2025},
  doi = {10.1007/s11095-025-03967-4}
}
Kostenlos starten →