EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

A new kinematic model for revolute clearance joints with noncircular bushing and pin in planar multibody systems

Zhe Liu, Heng Zhang, Lu Meng, Yu Sun, Sihai Luo, Liucheng Zhou, Pei Li

Nonlinear Dynamics · 2024-08 · 112 (15) · 12965-12993

DOI: 10.1007/s11071-024-09725-2 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Nonlinear Dynamics, online erschienen am 24.05.2024. Verfasst von Zhe Liu und 6 weiteren Autor:innen. Die Arbeit wurde bisher 12-mal zitiert (Crossref) und nennt 46 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: National Key Research and Development Program of China, University of Southern Denmark.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Due to manufacturing error and wear, the profiles of bushing and pin in revolute clearance joints are usually non-circular, while traditional kinematic models for revolute clearance joints generally assume a circular profile for the pin or bushing, which may not be able to accurately capture the kinematic behavior of real revolute joints in multibody systems. To this end, a curvature center method was proposed for the kinematic modeling of revolute clearance joints with noncircular bushing and pin. In the proposed method, both the noncircular bushing and pin were discretized, and the curvature center and radius corresponding to each discrete point were then obtained to detect the point of contact between the bushing and pin based on their kinematic constraints. The number of discrete points was determined based on both accuracy and efficiency of the proposed curvature center method, which was then applied to model a revolute clearance joint between the slider and the link of a slider-crank mechanism. Via comparison to the traditional geometric center method and discrete point method, it was validated that the proposed method can achieve a comparable accuracy in modeling revolute joints with a circular pin. The unique advantage of the proposed curvature center method is its ability in modeling revolute joints with noncircular bushing and noncircular pin, which was also demonstrated via a series of simulations. Simulation results show a significant influence of noncircular bushing and noncircular pin on the dynamic response of the multibody system. This implies the promising value of the proposed method in studying the effect of manufacturing error or wear of both bushing and pin on the system’s dynamic performance and/or service life.

Förderung

  • National Key Research and Development Program of China
  • University of Southern Denmark

Zitieren

APA

Liu, Z., Zhang, H., Meng, L., Sun, Y., Luo, S., Zhou, L., & Li, P. (2024). A new kinematic model for revolute clearance joints with noncircular bushing and pin in planar multibody systems. Nonlinear Dynamics, 112(15), 12965-12993. https://doi.org/10.1007/s11071-024-09725-2

Vancouver

Liu Z, Zhang H, Meng L, Sun Y, Luo S, Zhou L, et al. A new kinematic model for revolute clearance joints with noncircular bushing and pin in planar multibody systems. Nonlinear Dynamics. 2024;112(15):12965-12993. doi:10.1007/s11071-024-09725-2

BibTeX
@article{Liu2024,
  author = {Liu, Zhe and Zhang, Heng and Meng, Lu and Sun, Yu and Luo, Sihai and Zhou, Liucheng and Li, Pei},
  title = {A new kinematic model for revolute clearance joints with noncircular bushing and pin in planar multibody systems},
  journal = {Nonlinear Dynamics},
  year = {2024},
  volume = {112},
  number = {15},
  pages = {12965--12993},
  doi = {10.1007/s11071-024-09725-2}
}
Kostenlos starten →