EUVIMEDEUVIMED entdecken
Open Access · CC BY-NC-ND 4.0

PLA/hydroxyapatite composite scaffolds fabricated by digital light processing for bone regeneration

V J Garrido Hernández, D Sánchez Campos, C Velasco Santos, L S Villaseñor-Cerón, R Villafuerte-Segura, V Rodríguez Lugo

Journal of Materials Science: Materials in Medicine · 26.05.2026 · 37 (1)

DOI: 10.1007/s10856-026-07079-2 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Journal of Materials Science: Materials in Medicine, online erschienen am 26.05.2026. Verfasst von V J Garrido Hernández und 5 weiteren Autor:innen. Beteiligte Einrichtung: Área Académica de Ciencias de la Tierra y Materiales, Instituto de Ciencias Básicas e Ingeniería, Universidad Autónoma del Estado de Hidalgo, Pachuca…. Hauptthemen laut MEDLINE: Polyesters, Durapatite, Tissue Scaffolds, Bone Regeneration. Die Arbeit wurde bisher 2-mal zitiert (Crossref) und nennt 41 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY-NC-ND 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Bone tissue regeneration faces a major challenge: traditional therapies such as autografts and allografts are limited by donor site morbidity, restricted availability, and potential immune rejection. Therefore, there is a pressing need to develop synthetic scaffolds that mimic the extracellular matrix while providing adequate mechanical, morphological, and biological properties to promote osteogenesis and angiogenesis. In this study, polylactic acid/hydroxyapatite (PLA/HAp) scaffolds were designed using Digital Light Processing (DLP) 3D printing technology, strategically integrating HAp nanoparticles (NPs) at concentrations ranging from 0 to 5 wt%. The scaffolds exhibited a biomimetic cylindrical architecture with interconnected square pores of 350 µm and a theoretical porosity of 78% calculated from the CAD models. Finite element analysis (FEM) revealed high structural stability under physiological loads, with maximum displacements of 3.09 × 10⁻² mm and stress levels well below the elastic limit of polylactic acid (PLA). Morphological characterization by scanning electron microscopy (SEM) showed a progressive increase in surface roughness with higher HAp content, without agglomeration, as confirmed by energy dispersive spectroscopy (EDS) mapping. Cell viability studies using 3T3-L1 fibroblasts demonstrated a significant increase in metabolic activity, with the M4 (4%) and M5 (5%) samples reaching viabilities of 79.8% and 86.1%, respectively, classifying them as highly biocompatible according to ISO 10993-5. These results demonstrate that DLP printing enables the synthesis and design of PLA/HAp cellular scaffolds with precise geometry, excellent mechanical performance, and tunable bioactive properties, positioning them as a promising alternative for bone tissue engineering.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

PolyestersDurapatiteTissue ScaffoldsBone RegenerationAnimalsMiceTissue EngineeringPrinting, Three-DimensionalMaterials TestingCell SurvivalMicroscopy, Electron, ScanningPorosityFinite Element AnalysisBiocompatible MaterialsSurface Properties

Substanzen

PolyestersDurapatitepoly(lactide)Biocompatible Materials

Autor:innen und Institutionen

  • Área Académica de Ciencias de la Tierra y Materiales, Instituto de Ciencias Básicas e Ingeniería, Universidad Autónoma del Estado de Hidalgo, Pachuca, Hidalgo, México.
  • Instituto de Física, Universidad Autónoma de San Luis Potosí, San Luis Potosí, México.
  • Tecnológico Nacional de México-Instituto Tecnológico de Querétaro, División de Estudios de Posgrado e Investigación, Av. Tecnológico s/n esquina Gral. Mariano Escobedo, Col. Centro Histórico, Querétaro, México.
  • Área Académica de Computación y Electrónica, Universidad Autónoma del Estado de Hidalgo, Pachuca, Hidalgo, México.
  • Área Académica de Ciencias de la Tierra y Materiales, Instituto de Ciencias Básicas e Ingeniería, Universidad Autónoma del Estado de Hidalgo, Pachuca, Hidalgo, México. ventura.rl65@gmail.com.

Zitieren

APA

Hernández, V. J. G., Campos, D. S., Santos, C. V., Villaseñor-Cerón, L. S., Villafuerte-Segura, R., & Rodríguez Lugo, V. (2026). PLA/hydroxyapatite composite scaffolds fabricated by digital light processing for bone regeneration. Journal of Materials Science: Materials in Medicine, 37(1). https://doi.org/10.1007/s10856-026-07079-2

Vancouver

Hernández VJG, Campos DS, Santos CV, Villaseñor-Cerón LS, Villafuerte-Segura R, Rodríguez Lugo V. PLA/hydroxyapatite composite scaffolds fabricated by digital light processing for bone regeneration. Journal of Materials Science: Materials in Medicine. 2026;37(1). doi:10.1007/s10856-026-07079-2

BibTeX
@article{Hernndez2026,
  author = {Hernández, V J Garrido and Campos, D Sánchez and Santos, C Velasco and Villaseñor-Cerón, L S and Villafuerte-Segura, R and Rodríguez Lugo, V},
  title = {PLA/hydroxyapatite composite scaffolds fabricated by digital light processing for bone regeneration},
  journal = {Journal of Materials Science: Materials in Medicine},
  year = {2026},
  volume = {37},
  number = {1},
  doi = {10.1007/s10856-026-07079-2}
}
Kostenlos starten →