Selective mycobacterial capture with ultraviolet-polymerized poly-dimethyldiallyl chloride functionalized surfaces
Journal of Materials Science: Materials in Medicine · 2024
DOI: 10.1007/s10856-024-06829-4 ↗Kurz gefasst
Fachartikel in der Zeitschrift Journal of Materials Science: Materials in Medicine, 2024. Verfasst von Xuesong Jiang und 8 weiteren Autor:innen. Beteiligte Einrichtung: Department of Materials Science and Engineering, Whiting School of Engineering, Johns Hopkins University, Baltimore, 21218, MD, USA. Hauptthemen laut MEDLINE: Ultraviolet Rays. Die Arbeit wurde bisher 1-mal zitiert (Crossref) und nennt 26 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).
Abstract (Originalsprache)
Tuberculosis (TB) is the top cause of death from a single infectious pathogen after COVID-19. Despite molecular diagnostic advances, two-thirds of the 10 million annual TB cases are still diagnosed using direct smear microscopy which has ~50% sensitivity. To increase the analytical performance of smear microscopy, we developed and characterized a novel polymer (Polydiallyldimethylammonium chloride [PDADMAC]) engraftment on inexpensive polystyrene (PS) specifically functionalized for mycobacterial capture. Engraftment is achieved via UV photopolymerization of DADMAC monomer on plasma-activated PS. The platform was tested on sputum from presumptive TB cases in Kampala, Uganda ( n = 50), with an increased overall sensitivity of 81.8% (27/33) vs. fluorescent smear microscopy 57% (19/33) compared to a molecular (Cepheid GeneXpert MTB/RIF) gold standard. Frugal smear diagnostic innovation that is rapid and does not require dedicated instrumentation may offer an important solution to bridge the TB diagnostic gap. Graphical Abstract
Schlagwörter
MeSH-Schlagwörter (MEDLINE)
Substanzen
Autor:innen und Institutionen
- Department of Materials Science and Engineering, Whiting School of Engineering, Johns Hopkins University, Baltimore, 21218, MD, USA.
- Institute for NanoBioTechnology, Johns Hopkins University, Baltimore, 21218, MD, USA.
- Translational Tissue Engineering Center, School of Medicine, Johns Hopkins University, Baltimore, 21287, MD, USA.
- Center for Bioengineering Innovation and Design, Johns Hopkins University, Baltimore, 21218, MD, USA. bmathek1@jhu.edu.
- Center for Bioengineering Innovation and Design, Johns Hopkins University, Baltimore, 21218, MD, USA.
- Departments of Plastic and Reconstructive Surgery, School of Medicine, Johns Hopkins University, Baltimore, 21205, MD, USA.
Zitieren
APA
Jiang, X., Mathekga, B. S. P., Singh, D., Coon, D., Sinha, A., Armstrong, D., Acharya, S., Mao, H. Q., & Manabe, Y. C. (2024). Selective mycobacterial capture with ultraviolet-polymerized poly-dimethyldiallyl chloride functionalized surfaces. Journal of Materials Science: Materials in Medicine. https://doi.org/10.1007/s10856-024-06829-4
Vancouver
Jiang X, Mathekga BSP, Singh D, Coon D, Sinha A, Armstrong D, et al. Selective mycobacterial capture with ultraviolet-polymerized poly-dimethyldiallyl chloride functionalized surfaces. Journal of Materials Science: Materials in Medicine. 2024. doi:10.1007/s10856-024-06829-4
BibTeX
@article{Jiang2024,
author = {Jiang, Xuesong and Mathekga, Bonolo S P and Singh, Digvijay and Coon, Devin and Sinha, Anjana and Armstrong, Derek and Acharya, Soumyadipta and Mao, Hai-Quan and Manabe, Yukari C},
title = {Selective mycobacterial capture with ultraviolet-polymerized poly-dimethyldiallyl chloride functionalized surfaces},
journal = {Journal of Materials Science: Materials in Medicine},
year = {2024},
doi = {10.1007/s10856-024-06829-4}
}
EUVIMED