Study of Zn–Ag alloys prepared via powder metallurgy
Journal of Materials Science · 2026-07 · 61 (27) · 19775-19799
DOI: 10.1007/s10853-026-12950-2 ↗Kurz gefasst
Fachartikel in der Zeitschrift Journal of Materials Science, online erschienen am 30.05.2026. Verfasst von V. Čákyová und 8 weiteren Autor:innen. Die Arbeit nennt 106 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Agentúra na Podporu Výskumu a Vývoja, Internal Research Grant of Faculty of Science of P. J. Šafárik University, Pavol Jozef Šafárik University in Košice.
Abstract (Originalsprache)
Orthopaedic biomaterials require a balance between mechanical integrity and controlled degradation. Among biodegradable metals, magnesium-based alloys degrade too rapidly, leading to premature loss of mechanical support, whereas iron-based alloys exhibit slow degradation and high stiffness, which may limit their clinical applicability. In contrast, zinc-based materials offer a more favourable combination of moderate corrosion rate and mechanical properties closer to natural bone. However, the relatively low mechanical strength of pure zinc remains a critical limitation, highlighting the need for effective alloying and processing strategies. In this context, the incorporation of silver represents a promising approach to enhance both the mechanical strength and antibacterial performance of zinc. Despite this potential, the combined effect of composition and processing route, particularly cost-effective techniques such as powder metallurgy, on the structural and functional behaviour of Zn-Ag systems remains insufficiently understood. In this study, binary alloys Zn-xAg ( x = 2.0, 4.0, 6.0 wt% Ag) and pure Zn were prepared using powder metallurgy. The structure, corrosion behaviour, surface morphology, and wettability were evaluated. The highest corrosion rate of 0.353 mm year −1 was observed for the pure Zn sample. Atomic force microscopy revealed that the surface of pure zinc was the smoothest, while the roughness of Zn-Ag alloys increased with silver content. X-ray diffraction analysis confirmed the presence of intermetallic phases. Furthermore, contact angle measurements indicated slightly hydrophilic surfaces, which could promote cell adhesion. These findings demonstrate that Zn-Ag alloys processed via powder metallurgy represent a promising strategy for tailoring the mechanical and functional performance of zinc-based implants.
Förderung
- Agentúra na Podporu Výskumu a Vývoja
- Internal Research Grant of Faculty of Science of P. J. Šafárik University
- Pavol Jozef Šafárik University in Košice
Zitieren
APA
Čákyová, V., Gorejová, R., Kupková, M., Džupon, M., Sopčák, T., Faberová, M., Ozaltin, K., Strečková, M., & Oriňaková, R. (2026). Study of Zn–Ag alloys prepared via powder metallurgy. Journal of Materials Science, 61(27), 19775-19799. https://doi.org/10.1007/s10853-026-12950-2
Vancouver
Čákyová V, Gorejová R, Kupková M, Džupon M, Sopčák T, Faberová M, et al. Study of Zn–Ag alloys prepared via powder metallurgy. Journal of Materials Science. 2026;61(27):19775-19799. doi:10.1007/s10853-026-12950-2
BibTeX
@article{kyov2026,
author = {Čákyová, V. and Gorejová, R. and Kupková, M. and Džupon, M. and Sopčák, T. and Faberová, M. and Ozaltin, K. and Strečková, M. and Oriňaková, R.},
title = {Study of Zn–Ag alloys prepared via powder metallurgy},
journal = {Journal of Materials Science},
year = {2026},
volume = {61},
number = {27},
pages = {19775--19799},
doi = {10.1007/s10853-026-12950-2}
}
EUVIMED