EUVIMEDEUVIMED entdecken
VergleichsstudieOpen Access · CC BY 4.0

Enhancing Bone Scaffold Fabrication: A Comparative Study of Manual Casting and Automated 3D Bioprinting

Yasser Ahmed, Ali S Alshami, Ashraf Al-Goraee, Collins P Obeng, Rebecca Kennedy, Hesham Abdelaziz, Ryan Striker

Annals of Biomedical Engineering · 2025-09 · 53 (9) · 2059-2070

DOI: 10.1007/s10439-025-03752-9 ↗

Kurz gefasst

Vergleichsstudie in der Zeitschrift Annals of Biomedical Engineering, online erschienen am 05.06.2025. Verfasst von Yasser Ahmed und 6 weiteren Autor:innen. Beteiligte Einrichtung: Biomedical Engineering Department, University of North Dakota, Grand Forks, ND, 58202, USA. Hauptthemen laut MEDLINE: Tissue Scaffolds, Printing, Three-Dimensional, Bioprinting, Mesenchymal Stem Cells. Die Arbeit wurde bisher 8-mal zitiert (Crossref) und nennt 42 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: NIGMS NIH HHS, North Dakota Established Program to Stimulate Competitive Research, National Institute for Health Care Management Foundation.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

While fabrication of bone scaffolds is important for the development of tissue engineering, traditional techniques have typically been prone to either scaling or reproducibility issues. This paper highlights a strategy for automated 3D printing and bioprinting techniques that enhance precision and efficiency in the production of PLGA–HA scaffolds. We realized significant improvements in efficiency, reproducibility, and scalability through optimization of 3D printing parameters, improvement of material handling, and refinement of the fabrication process. Precise measurement consequently minimized material waste; the introduction of a mesh filter allowed for high-throughput experimentation without compromising the integrity of individual scaffolds, streamlining the workflow. Combining automated casting with state-of-the-art 3D bioprinting, our experimental methodology precisely applied the bioactive materials, reducing the processing time fivefold and enhancing precision. Besides, automated casting produced thicker, better-quality scaffolds averaging 0.02354 g, which is against 0.01169 g using the manual approach, effectively doubling the retention of the PLGA–HA coating on a PVA mold. Excellent cell viability and adhesion on automated scaffolds have been further underlined for application in tissue engineering during in vitro studies using multipotent mesenchymal stromal cells. Although conventional techniques, such as injection molding, are standard for large lots, 3D printing has advantages in scaffold fabrication regarding control over geometry and homogeneous material properties. Equally important, these characteristics are necessary to achieve repeatable and up-scaled experimental results.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Tissue ScaffoldsPrinting, Three-DimensionalBioprintingMesenchymal Stem CellsTissue EngineeringPolylactic Acid-Polyglycolic Acid CopolymerHumansPolyglycolic AcidLactic AcidDurapatite

Stichwörter der Autor:innen

3D printingAutomationBioprintingBone regenerationIn vitroTissue engineering

Substanzen

Polylactic Acid-Polyglycolic Acid CopolymerPolyglycolic AcidLactic AcidDurapatite

Autor:innen und Institutionen

  • Biomedical Engineering Department, University of North Dakota, Grand Forks, ND, 58202, USA.
  • Department of Chemical Engineering, University of North Dakota, Grand Forks, ND, 58202, USA. yasser.ahmed@und.edu.
  • Department of Chemical Engineering, University of North Dakota, Grand Forks, ND, 58202, USA.

Förderung

  • NIGMS NIH HHS
  • North Dakota Established Program to Stimulate Competitive Research
  • National Institute for Health Care Management Foundation

Zitieren

APA

Ahmed, Y., Alshami, A. S., Al-Goraee, A., Obeng, C. P., Kennedy, R., Abdelaziz, H., & Striker, R. (2025). Enhancing Bone Scaffold Fabrication: A Comparative Study of Manual Casting and Automated 3D Bioprinting. Annals of Biomedical Engineering, 53(9), 2059-2070. https://doi.org/10.1007/s10439-025-03752-9

Vancouver

Ahmed Y, Alshami AS, Al-Goraee A, Obeng CP, Kennedy R, Abdelaziz H, et al. Enhancing Bone Scaffold Fabrication: A Comparative Study of Manual Casting and Automated 3D Bioprinting. Annals of Biomedical Engineering. 2025;53(9):2059-2070. doi:10.1007/s10439-025-03752-9

BibTeX
@article{Ahmed2025,
  author = {Ahmed, Yasser and Alshami, Ali S and Al-Goraee, Ashraf and Obeng, Collins P and Kennedy, Rebecca and Abdelaziz, Hesham and Striker, Ryan},
  title = {Enhancing Bone Scaffold Fabrication: A Comparative Study of Manual Casting and Automated 3D Bioprinting},
  journal = {Annals of Biomedical Engineering},
  year = {2025},
  volume = {53},
  number = {9},
  pages = {2059--2070},
  doi = {10.1007/s10439-025-03752-9}
}
Kostenlos starten →