EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

A Novel Approach for Multiple Material Extrusion in Arthroscopic Knee Surgery

Tommaso Mazzocchi, Daniele Guarnera, Diego Trucco, Francesco Rocco Restaino, Lorenzo Vannozzi, Alessio Siliberto, Gina Lisignoli, Stefano Zaffagnini, Alessandro Russo, Leonardo Ricotti

Annals of Biomedical Engineering · 2023-03 · 51 (3) · 550-565

DOI: 10.1007/s10439-022-03061-5 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Annals of Biomedical Engineering, online erschienen am 03.09.2022. Verfasst von Tommaso Mazzocchi und 9 weiteren Autor:innen. Beteiligte Einrichtung: The BioRobotics Institute, Scuola Superiore Sant'Anna, Piazza Martiri della Liberta' 33, 56127, Pisa, Italy. Hauptthemen laut MEDLINE: Cartilage, Articular, Osteoarthritis, Knee. Die Arbeit wurde bisher 4-mal zitiert (Crossref) und nennt 56 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: H2020 European Research Council, Scuola Superiore Sant'Anna.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Articular cartilage defects and degenerative diseases are pathological conditions that cause pain and the progressive loss of joint functionalities. The most severe cases are treated through partial or complete joint replacement with prostheses, even if the interest in cartilage regeneration and re-growth methods is steadily increasing. These methods consist of the targeted deposition of biomaterials. Only a few tools have been developed so far for performing these procedures in a minimally invasive way. This work presents an innovative device for the direct deposition of multiple biomaterials in an arthroscopic scenario. The tool is easily handleable and allows the extrusion of three different materials simultaneously. It is also equipped with a flexible tip to reach remote areas of the damaged cartilage. Three channels are arranged coaxially and a spring-based dip-coating approach allows the fabrication and assembly of a bendable polymeric tip. Experimental tests were performed to characterize the tip, showing the ability to bend it up to 90° (using a force of ~ 1.5 N) and to extrude three coaxial biomaterials at the same time with both tip straight and tip fully bent. Rheometric analysis and fluid-dynamic computational simulations were performed to analyze the fluids’ behavior; the maximum shear stresses were observed in correspondence to the distal tip and the channel convergence chamber, but with values up to ~ 1.2 kPa, compatible with a safe extrusion of biomaterials, even laden with cells. The cells viability was assessed after the extrusion with Live/Dead assay, confirming the safety of the extrusion procedures. Finally, the tool was tested arthroscopically in a cadaveric knee, demonstrating its ability to deliver the biomaterial in different areas, even ones that are typically hard-to-reach with traditional tools.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Cartilage, ArticularOsteoarthritis, KneeHumansKnee JointArthroscopyCell SurvivalBiocompatible Materials

Stichwörter der Autor:innen

Arthroscopic surgeryArthroscopic toolsBiomaterialsCartilage regenerationMedical devicesOsteoarthritis

Substanzen

Biocompatible Materials

Autor:innen und Institutionen

  • The BioRobotics Institute, Scuola Superiore Sant'Anna, Piazza Martiri della Liberta' 33, 56127, Pisa, Italy.
  • Department of Excellence in Robotics & AI, Scuola Superiore Sant'Anna, Piazza Martiri della Liberta' 33, 56127, Pisa, Italy.
  • The BioRobotics Institute, Scuola Superiore Sant'Anna, Piazza Martiri della Liberta' 33, 56127, Pisa, Italy. daniele.guarnera@santannapisa.it.
  • Department of Excellence in Robotics & AI, Scuola Superiore Sant'Anna, Piazza Martiri della Liberta' 33, 56127, Pisa, Italy. daniele.guarnera@santannapisa.it.
  • IRCCS Istituto Ortopedico Rizzoli, SC Laboratorio di Immunoreumatologia e Rigenerazione Tissutale, Via di Barbiano, 1/10, 40136, Bologna, Italy.
  • IRCCS Istituto Ortopedico Rizzoli, Orthopaedic and Traumatologic Clinic, Via di Barbiano, 1/10, 40136, Bologna, Italy.

Förderung

  • H2020 European Research Council
  • Scuola Superiore Sant'Anna

Zitieren

APA

Mazzocchi, T., Guarnera, D., Trucco, D., Restaino, F. R., Vannozzi, L., Siliberto, A., Lisignoli, G., Zaffagnini, S., Russo, A., & Ricotti, L. (2023). A Novel Approach for Multiple Material Extrusion in Arthroscopic Knee Surgery. Annals of Biomedical Engineering, 51(3), 550-565. https://doi.org/10.1007/s10439-022-03061-5

Vancouver

Mazzocchi T, Guarnera D, Trucco D, Restaino FR, Vannozzi L, Siliberto A, et al. A Novel Approach for Multiple Material Extrusion in Arthroscopic Knee Surgery. Annals of Biomedical Engineering. 2023;51(3):550-565. doi:10.1007/s10439-022-03061-5

BibTeX
@article{Mazzocchi2023,
  author = {Mazzocchi, Tommaso and Guarnera, Daniele and Trucco, Diego and Restaino, Francesco Rocco and Vannozzi, Lorenzo and Siliberto, Alessio and Lisignoli, Gina and Zaffagnini, Stefano and Russo, Alessandro and Ricotti, Leonardo},
  title = {A Novel Approach for Multiple Material Extrusion in Arthroscopic Knee Surgery},
  journal = {Annals of Biomedical Engineering},
  year = {2023},
  volume = {51},
  number = {3},
  pages = {550--565},
  doi = {10.1007/s10439-022-03061-5}
}
Kostenlos starten →