EUVIMEDEUVIMED entdecken
Crossref

Overall fit of anterior and posterior single crown substructures fabricated with different additive manufacturing and conventional techniques

Gürel Pekkan, Hilal Gülgezen Aydın, Süleyman Hakan Tuna, Canan Hekimoğlu

Odontology · 2025

DOI: 10.1007/s10266-025-01178-2 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Odontology, 2025. Verfasst von Gürel Pekkan und 3 weiteren Autor:innen. Beteiligte Einrichtung: Department of Prosthodontics, Faculty of Dentistry, Tekirdag Namik Kemal University, Degirmenalti Yerleskesi, 59030, Suleymanpasa, Tekirdag, Türkiye. Hauptthemen laut MEDLINE: Crowns, Dental Prosthesis Design, Dental Marginal Adaptation. Die Arbeit nennt 48 Literaturangaben. Gefördert von: Kutahya Dumlupinar University Scientific Research Projects Fund.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Marginal and internal fit of single crowns is critical for clinical success. Further research is necessary to investigate the effects of various conventional and additive/subtractive manufacturing techniques on restoration fit, particularly for different tooth types. This in vitro study compared the fit of anterior and posterior crown substructures fabricated using five techniques: milled wax patterns for casting (CAW), 3D-printed polymer patterns for casting (3DP), direct metal laser sintering (DMLS), selective laser melting (SLM), and manual wax carving (Cast). The maxillary lateral and first molar teeth were prepared on a polyamide model, and substructures were designed after scanning. Cobalt-chromium (Co-Cr) specimens were fabricated for each technique (n = 10). Discrepancies were measured using the silicone replica technique and analyzed with two-way ANOVA and Bonferroni tests (α = .05). The 3DP group exhibited the highest overall discrepancies, while DMLS had the highest for molars, and DMLS, Cast, and SLM had the highest for laterals, respectively (p < 0.05). Tooth type significantly affected chamfer (p = 0.023, partial η2 = 0.283), axial (p = 0.009, partial η2 = 0.017), and incisal/occlusal discrepancies (p < 0.001, partial η2 = 0.083). Significant differences were noted among fabrication techniques regarding overall, marginal, chamfer, axial, and incisal/occlusal discrepancies (p < 0.001). The DMLS technique showed results comparable to manual wax carving, demonstrating superior marginal and internal adaptation in posterior substructures (p < 0.05).

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

CrownsDental Prosthesis DesignDental Marginal AdaptationHumansComputer-Aided DesignIn Vitro TechniquesDental Casting TechniquePrinting, Three-DimensionalMolar

Stichwörter der Autor:innen

3D printingAdditive manufacturingCAD-CAMInternal fitMarginal fit

Autor:innen und Institutionen

  • Department of Prosthodontics, Faculty of Dentistry, Tekirdag Namik Kemal University, Degirmenalti Yerleskesi, 59030, Suleymanpasa, Tekirdag, Türkiye.
  • Department of Prosthodontics, Faculty of Dentistry, Tekirdag Namik Kemal University, Degirmenalti Yerleskesi, 59030, Suleymanpasa, Tekirdag, Türkiye. hgaydin@nku.edu.tr.
  • Department of Prosthodontics, Faculty of Dentistry, Dokuz Eylül University, Izmir, Türkiye.
  • Department of Prosthodontics, Faculty of Dentistry, Hacettepe University, Ankara, Türkiye.

Förderung

  • Kutahya Dumlupinar University Scientific Research Projects Fund

Zitieren

APA

Pekkan, G., Gülgezen Aydın, H., Tuna, S. H., & Hekimoğlu, C. (2025). Overall fit of anterior and posterior single crown substructures fabricated with different additive manufacturing and conventional techniques. Odontology. https://doi.org/10.1007/s10266-025-01178-2

Vancouver

Pekkan G, Gülgezen Aydın H, Tuna SH, Hekimoğlu C. Overall fit of anterior and posterior single crown substructures fabricated with different additive manufacturing and conventional techniques. Odontology. 2025. doi:10.1007/s10266-025-01178-2

BibTeX
@article{Pekkan2025,
  author = {Pekkan, Gürel and Gülgezen Aydın, Hilal and Tuna, Süleyman Hakan and Hekimoğlu, Canan},
  title = {Overall fit of anterior and posterior single crown substructures fabricated with different additive manufacturing and conventional techniques},
  journal = {Odontology},
  year = {2025},
  doi = {10.1007/s10266-025-01178-2}
}
Kostenlos starten →