EUVIMEDEUVIMED entdecken
Crossref

Stress analysis method for ascending aortic aneurysm based on unloaded geometry with non-uniform thickness distribution

Xiaoyu Liu, Zhihong Lin, Shihua Zhao, Fei Li, Qi Gao

Biomechanics and Modeling in Mechanobiology · 2025

DOI: 10.1007/s10237-025-01949-4 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Biomechanics and Modeling in Mechanobiology, 2025. Verfasst von Xiaoyu Liu und 4 weiteren Autor:innen. Beteiligte Einrichtung: School of Aeronautics and Astronautics, Zhejiang University, Hangzhou, China. Hauptthemen laut MEDLINE: Stress, Mechanical, Aorta, Aortic Aneurysm, Aortic Aneurysm, Thoracic. Die Arbeit nennt 58 Literaturangaben. Gefördert von: National Natural Science Foundation of China.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Using finite element method (FEM) to compute wall stress is now a common way to assess ascending thoracic aortic aneurysms (ATAA) severity. Medical images can provide aortic geometry for FEM, but thickness information is lacked and the geometry is at loaded state. Therefore, in this study, an unloaded geometry with a non-uniform thickness distribution is reconstructed. Measurements of wall thickness are taken from resected tissue to accurately replicate the thickness distribution. Subsequently, a novel method, derived from the existing fixed-point iterative (FPI) approach, is developed and applied to estimate the unloaded aortic geometry. This new method involves updating the relaxation factor at each iteration to improve robustness by constraining it within a threshold and normalizing it. Compared to the traditional FPI method, this novel approach is better tailored to the aortic geometries examined in this study. The study compares stress results obtained from models with uniform and non-uniform aortic wall thickness, both with and without assuming unloaded conditions. Findings indicate that stress distribution of non-uniform geometry matches better to the measured damage extent. Stress distribution of unloaded geometry is similar to that of loaded geometry, while the use of unloaded geometry enhances the stress gradient. The stress analysis reveals variations across different directions and regions, with the second principal stress (SPS) magnitude that is more sensitive to the circumferential region than the first principal stress (FPS) and von Mises stress (VMS). There is an overlap area between the high SPS region and the most expanded region. The most dilated area usually matched with high SPS region for loaded and unloaded geometry or uniform and non-uniform geometry. Thus, although magnitude of SPS is smaller than that of FPS and of VMS, it is suggested to pay more attention to SPS in severity assessment of ATAA aneurysm.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Stress, MechanicalAortaAortic AneurysmAortic Aneurysm, ThoracicHumansFinite Element AnalysisModels, CardiovascularAneurysm, Ascending Aorta

Stichwörter der Autor:innen

Aortic aneurysmFinite element analysisStressUnloaded geometryVessel thickness

Autor:innen und Institutionen

  • School of Aeronautics and Astronautics, Zhejiang University, Hangzhou, China.
  • State Key Laboratory of Transvascular Implantation Devices, Zhejiang University, Hangzhou, China.
  • Department of Magnetic Resonance Imaging, Fuwai Hospital, Chinese Academy of Medical Sciences, Beijing, China.
  • Heart Valve and Atrial Fibrillation Center, Beijing Anzhen Hospital, Capital Medical University, Beijing, China. drfeili@mail.ccmu.edu.cn.
  • School of Aeronautics and Astronautics, Zhejiang University, Hangzhou, China. qigao@zju.edu.cn.
  • State Key Laboratory of Transvascular Implantation Devices, Zhejiang University, Hangzhou, China. qigao@zju.edu.cn.

Förderung

  • National Natural Science Foundation of China

Zitieren

APA

Liu, X., Lin, Z., Zhao, S., Li, F., & Gao, Q. (2025). Stress analysis method for ascending aortic aneurysm based on unloaded geometry with non-uniform thickness distribution. Biomechanics and Modeling in Mechanobiology. https://doi.org/10.1007/s10237-025-01949-4

Vancouver

Liu X, Lin Z, Zhao S, Li F, Gao Q. Stress analysis method for ascending aortic aneurysm based on unloaded geometry with non-uniform thickness distribution. Biomechanics and Modeling in Mechanobiology. 2025. doi:10.1007/s10237-025-01949-4

BibTeX
@article{Liu2025,
  author = {Liu, Xiaoyu and Lin, Zhihong and Zhao, Shihua and Li, Fei and Gao, Qi},
  title = {Stress analysis method for ascending aortic aneurysm based on unloaded geometry with non-uniform thickness distribution},
  journal = {Biomechanics and Modeling in Mechanobiology},
  year = {2025},
  doi = {10.1007/s10237-025-01949-4}
}
Kostenlos starten →