Leveraging three-dimensional craniofacial morphology for customized abutment design using facial scanning technology
Clinical Oral Investigations · 2025
DOI: 10.1007/s00784-025-06701-x ↗Kurz gefasst
Fachartikel in der Zeitschrift Clinical Oral Investigations, 2025. Verfasst von Kaijin Lin und 6 weiteren Autor:innen. Beteiligte Einrichtung: Clinical Research Center for Oral Tissue Deficiency Diseases of Fujian Province & Fujian Key Laboratory of Oral Diseases & Fujian Provincial Engineer…. Hauptthemen laut MEDLINE: Imaging, Three-Dimensional, Cone-Beam Computed Tomography, Face, Dental Abutments. Die Arbeit nennt 36 Literaturangaben. Gefördert von: Natural Science Foundation of Fujian Province.
Abstract (Originalsprache)
OBJECTIVES: This study aimed to investigate the correlation between the dental cervical morphology (DCM) of maxillary anterior teeth and facial parameters, with the goal of validating the predictive efficacy of these facial parameters for DCM of the maxillary anterior teeth in a Chinese population. MATERIALS AND METHODS: This cross-sectional study was conducted at Stomatology Hospital of Fujian Medical University. Facial parameters of participants were obtained using a 3D facial scanner and subsequently imported into reverse engineering software for measurement. Cone beam computed tomography (CBCT) data were imported into imaging software, where specific landmarks were annotated. The distance between these landmarks at the cemento-enamel junction (CEJ) level was then quantified and defined as dental cervical morphology (DCM). Pearson correlation analysis was employed to identify relationships between facial and DCM measurements. Linear regression was performed on significantly correlated variables, while t-tests evaluated the difference of real value and predicted value (α = 0.05). RESULTS: A total of 147 volunteers participated in this study. Significant correlations for DCM were observed with interlateral canthus width (LCW) in males (P 0.05), with LCW used for males and MCW for females (P > 0.05). CONCLUSIONS: DCM of the maxillary anterior teeth was found to be associated with facial width, with LCW serving as a potential predictor for males and MCW for females. These findings suggested that facial morphology could be a valuable predictor for DCM. CLINICAL RELEVANCE: Facial parameters offer a reliable basis for the precise design of customized abutments, enhancing the accuracy and efficiency of clinical prosthodontic treatments, particularly in implantology and aesthetic restoration. TRIAL REGISTRATION: This study was approved by the Biomedical Research Ethics Committee of Stomatology Hospital of Fujian Medical University (approval no. 2023-24).
Schlagwörter
MeSH-Schlagwörter (MEDLINE)
Stichwörter der Autor:innen
Autor:innen und Institutionen
- Clinical Research Center for Oral Tissue Deficiency Diseases of Fujian Province & Fujian Key Laboratory of Oral Diseases & Fujian Provincial Engineering Research Center of Oral Biomaterial, School and Hospital of Stomat…
- Stomatological Key laboratory of Fujian College and University & Institute of Stomatology & Research Center of Dental and Craniofacial Implants, School and Hospital of Stomatology, Fujian Medical University, Fuzhou, Chi…
- School of Dental Medicine, University of Pennsylvania, Philadelphia, PA, USA.
Förderung
- Natural Science Foundation of Fujian Province
Zitieren
APA
Lin, K., Guo, Y., Wu, S., Ning, W., Yang, J., Wu, D., & Guo, J. (2025). Leveraging three-dimensional craniofacial morphology for customized abutment design using facial scanning technology. Clinical Oral Investigations. https://doi.org/10.1007/s00784-025-06701-x
Vancouver
Lin K, Guo Y, Wu S, Ning W, Yang J, Wu D, et al. Leveraging three-dimensional craniofacial morphology for customized abutment design using facial scanning technology. Clinical Oral Investigations. 2025. doi:10.1007/s00784-025-06701-x
BibTeX
@article{Lin2025,
author = {Lin, Kaijin and Guo, Yongqing and Wu, Shuang and Ning, Wencan and Yang, Jin and Wu, Dong and Guo, Jianbin},
title = {Leveraging three-dimensional craniofacial morphology for customized abutment design using facial scanning technology},
journal = {Clinical Oral Investigations},
year = {2025},
doi = {10.1007/s00784-025-06701-x}
}
EUVIMED