EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

An in vitro analysis of marginal and internal fit of 3D-printed permanent molar endocrowns with different preparation designs

Izim Turker Kader, Safa Ozer, Burcin Arican

Clinical Oral Investigations · 30.05.2025 · 29 (6)

DOI: 10.1007/s00784-025-06414-1 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Clinical Oral Investigations, online erschienen am 30.05.2025. Verfasst von Izim Turker Kader und 2 weiteren Autor:innen. Beteiligte Einrichtung: Department of Prosthodontics, Bahçeşehir University School of Dental Medicine, Istanbul, Turkey. izim.turker@gmail.com. Hauptthemen laut MEDLINE: Printing, Three-Dimensional, Molar, Dental Marginal Adaptation, Dental Prosthesis Design. Die Arbeit wurde bisher 10-mal zitiert (Crossref) und nennt 38 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Bahcesehir University.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Objectives

The purpose of this study was to evaluate the influence of different preparation designs on the marginal and internal fit of 3D-printed permanent endocrowns. Materials and methods Typodont maxillary right first molars were prepared and divided into four groups based on different preparation designs: Group 1– butt joint with 2 mm pulp chamber depth, Group 2– butt joint with 4 mm depth, Group 3– shoulder with 2 mm depth, and Group 4– shoulder with 4 mm depth ( n = 16 each). The prepared teeth were scanned and replicated as 3D-printed resin dies. Permanent endocrowns were fabricated using a ceramic-filled hybrid material and seated with light-body silicone. All restorations were rescanned, and superimposition was performed using 3D analysis software to evaluate marginal, internal, pulp chamber, and overall gaps based on multipoint measurements at standardized locations. Data were statistically analyzed using Two-Way Robust ANOVA ( p < 0.05).

Results

No significant differences were found between preparation types and depths for internal and overall gap values ( p > 0.05). However, the highest marginal gap was measured in Group 1 (0.08 mm; p = 0.017), while the largest pulp chamber gap was recorded in Group 4 (0.15 mm; p < 0.001).

Conclusions

A 1 mm shoulder preparation with a 2 mm pulp chamber depth demonstrated superior marginal and pulp chamber fit compared to other designs. While internal fit did not significantly vary among groups, this design showed the most consistent adaptation overall, supporting its clinical preference for 3D-printed permanent endocrowns. Clinical relevance Different preparation designs may affect the fit of endocrowns. Clinicians can prefer an endocrown preparation design of 1 mm shoulder preparation with a 2 mm pulp chamber to improve the adaptation of 3D-printed permanent endocrown restorations.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Printing, Three-DimensionalMolarDental Marginal AdaptationDental Prosthesis DesignCrownsHumansIn Vitro Techniques

Stichwörter der Autor:innen

EndocrownsInternal gapMarginal gapPrintingProsthodonticsThree-Dimensional

Autor:innen und Institutionen

  • Department of Prosthodontics, Bahçeşehir University School of Dental Medicine, Istanbul, Turkey. izim.turker@gmail.com.
  • Dental Prosthesis Technology, Bahçeşehir University Vocational School of Health Services, Istanbul, Turkey.
  • Department of Endodontics, Bahçeşehir University School of Dental Medicine, Istanbul, Turkey.

Förderung

  • Bahcesehir University

Zitieren

APA

Turker Kader, I., Ozer, S., & Arican, B. (2025). An in vitro analysis of marginal and internal fit of 3D-printed permanent molar endocrowns with different preparation designs. Clinical Oral Investigations, 29(6). https://doi.org/10.1007/s00784-025-06414-1

Vancouver

Turker Kader I, Ozer S, Arican B. An in vitro analysis of marginal and internal fit of 3D-printed permanent molar endocrowns with different preparation designs. Clinical Oral Investigations. 2025;29(6). doi:10.1007/s00784-025-06414-1

BibTeX
@article{TurkerKader2025,
  author = {Turker Kader, Izim and Ozer, Safa and Arican, Burcin},
  title = {An in vitro analysis of marginal and internal fit of 3D-printed permanent molar endocrowns with different preparation designs},
  journal = {Clinical Oral Investigations},
  year = {2025},
  volume = {29},
  number = {6},
  doi = {10.1007/s00784-025-06414-1}
}
Kostenlos starten →