Effect of surface treatment strategies on bond strength of additively and subtractively manufactured hybrid materials for permanent crowns
Clinical Oral Investigations · 2024
DOI: 10.1007/s00784-024-05767-3 ↗Kurz gefasst
Fachartikel in der Zeitschrift Clinical Oral Investigations, 2024. Verfasst von Zhen Mao und 5 weiteren Autor:innen. Beteiligte Einrichtung: Department of Prosthodontics, Geriatric Dentistry and Craniomandibular Disorders, Charité- Universitätsmedizin Berlin, corporate member of Freie Univ…. Hauptthemen laut MEDLINE: Surface Properties, Computer-Aided Design, Dental Bonding, Crowns. Die Arbeit wurde bisher 42-mal zitiert (Crossref) und nennt 40 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Charité - Universitätsmedizin Berlin.
Abstract (Originalsprache)
Objectives
The purpose of this study is to evaluate the bond strength of different computer-aided design / computer-aided manufacturing (CAD/CAM) hybrid ceramic materials following different pretreatments.
Methods
A total of 306 CAD/CAM hybrid material specimens were manufactured, n = 102 for each material (VarseoSmile Crown plus [VSCP] by 3D-printing; Vita Enamic [VE] and Grandio Blocs [GB] by milling). Each material was randomly divided into six groups regarding different pretreatment strategies: control, silane, sandblasting (50 μm aluminum oxide particles), sandblasting + silane, etching (9% hydrofluorics acid), etching + silane. Subsequently, surface roughness (Ra) values, surface free energy (SFE) were measured. Each specimen was bonded with a dual-cured adhesive composite. Half of the specimens were subjected to thermocycling (5000 cycles, 5–55 °C). The shear bond strength (SBS) test was performed. Data were analyzed by using a two-way analysis of variance, independent t-test, and Mann-Whitney-U-test (α = 0.05).
Results
Material type ( p = 0.001), pretreatment strategy ( p < 0.001), and the interaction ( p < 0.001) all had significant effects on Ra value. However, only etching on VSCP and VE surface increased SFE value significantly. Regarding SBS value, no significant difference was found among the three materials ( p = 0.937), while the pretreatment strategy significantly influenced SBS ( p < 0.05). Etching on VSCP specimens showed the lowest mean value among all groups, while sandblasting and silane result in higher SBS for all test materials.
Conclusions
The bond strength of CAD/CAM hybrid ceramic materials for milling and 3D-printing was comparable. Sandblasting and silane coupling were suitable for both millable and printable materials, while hydrofluoric etching should not be recommended for CAD/CAM hybrid ceramic materials. Clinical relevance Since comparable evidence between 3D-printable and millable CAD/CAM dental hybrid materials is scarce, the present study gives clear guidance for pretreatment planning on different materials.
Schlagwörter
MeSH-Schlagwörter (MEDLINE)
Stichwörter der Autor:innen
Substanzen
Autor:innen und Institutionen
- Department of Prosthodontics, Geriatric Dentistry and Craniomandibular Disorders, Charité- Universitätsmedizin Berlin, corporate member of Freie Universität Berlin and Humboldt-Universität zu Berlin, Aßmannshauser Str.…
- Department of Prosthodontics, School of Dental Medicine, Martin-Luther-University, Magdeburger Str. 16, 06112, Halle, Germany.
Förderung
- Charité - Universitätsmedizin Berlin
Zitieren
APA
Mao, Z., Schmidt, F., Beuer, F., Yassine, J., Hey, J., & Prause, E. (2024). Effect of surface treatment strategies on bond strength of additively and subtractively manufactured hybrid materials for permanent crowns. Clinical Oral Investigations. https://doi.org/10.1007/s00784-024-05767-3
Vancouver
Mao Z, Schmidt F, Beuer F, Yassine J, Hey J, Prause E. Effect of surface treatment strategies on bond strength of additively and subtractively manufactured hybrid materials for permanent crowns. Clinical Oral Investigations. 2024. doi:10.1007/s00784-024-05767-3
BibTeX
@article{Mao2024,
author = {Mao, Zhen and Schmidt, Franziska and Beuer, Florian and Yassine, Jamila and Hey, Jeremias and Prause, Elisabeth},
title = {Effect of surface treatment strategies on bond strength of additively and subtractively manufactured hybrid materials for permanent crowns},
journal = {Clinical Oral Investigations},
year = {2024},
doi = {10.1007/s00784-024-05767-3}
}
EUVIMED