EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

3D printed electrode-microwell system: a novel electrochemical platform for miRNA detection

Panagiota M Kalligosfyri, Chloe Miller, Stefano Cinti, Bhavik Anil Patel

Microchimica Acta · 2025-05 · 192 (5)

DOI: 10.1007/s00604-025-07190-1 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Microchimica Acta, online erschienen am 01.05.2025. Verfasst von Panagiota M Kalligosfyri und 3 weiteren Autor:innen. Beteiligte Einrichtung: Department of Pharmacy, University of Naples Federico II, 80131, Naples, Italy. Hauptthemen laut MEDLINE: MicroRNAs, Printing, Three-Dimensional, Electrochemical Techniques, Biosensing Techniques. Die Arbeit wurde bisher 26-mal zitiert (Crossref) und nennt 62 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: AIRC under MFAG 2022, Fondazione Umberto Veronesi Postdoctoral Fellowship 2025, Pathogen Readiness Platform for CERIC-ERIC.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

3D printing has enabled the ability to make creative electrochemical well designs suitable for a wide field of electrochemical sensing. The demand for robust electrochemical systems is particularly high in diagnostics, where the rapid detection of emerging biomarkers associated with severe diseases is critical for rapid medical decision-making. This study is aimed at developing a fully 3D-printed electrochemical sensing device featuring a three-electrode system fabricated from conductive printing materials and incorporating a microwell as the sensing platform. The assay principle of a robust electrochemical screen-printed sensor was adapted for this platform, incorporating a well-structured design to enhance fluid control. This structure ensured the uniform distribution of reagents across the sensing surface, improving the reproducibility and consistency of measurements and enabling the reliable detection of a microRNA target associated with lung cancer. The detection process was based on the hybridization of the target miRNA with an immobilized DNA probe labeled with methylene blue as a redox mediator. The sensor was thoroughly characterized and optimized, achieving a dynamic detection range of 0.001 to 400 nM and a lower limit of detection compared to screen-printed sensors, down to the picomolar level. Furthermore, the sensor demonstrated high selectivity for the target miRNA compared to other miRNA sequences, proving its specificity. These results highlighted the potential of 3D printing technology for the development of sensitive and selective tools for biomarker detection, making it a valuable complementary method in the field of diagnostics. Graphical Abstract

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

MicroRNAsPrinting, Three-DimensionalElectrochemical TechniquesBiosensing TechniquesElectrodesHumansLimit of DetectionDNA ProbesImmobilized Nucleic AcidsNucleic Acid HybridizationMethylene Blue

Stichwörter der Autor:innen

3D printingConductive PLADiagnosticsElectroanalysisMiRNASquare wave voltammetry

Substanzen

MicroRNAsDNA ProbesImmobilized Nucleic AcidsMethylene Blue

Autor:innen und Institutionen

  • Department of Pharmacy, University of Naples Federico II, 80131, Naples, Italy.
  • Centre for Lifelong Health and School of Applied Sciences, University of Brighton, Brighton, BN2 4GJ, UK.
  • Department of Pharmacy, University of Naples Federico II, 80131, Naples, Italy. stefano.cinti@unina.it.
  • Bioelectronics Task Force at University of Naples Federico II, Via Cinthia 21, 80126, Naples, Italy. stefano.cinti@unina.it.
  • Sbarro Institute for Cancer Research and Molecular Medicine, Center for Biotechnology, College of Science and Technology, Temple University, Philadelphia, PA, 19122, USA. stefano.cinti@unina.it.
  • Centre for Lifelong Health and School of Applied Sciences, University of Brighton, Brighton, BN2 4GJ, UK. b.a.patel@brighton.ac.uk.

Förderung

  • AIRC under MFAG 2022
  • Fondazione Umberto Veronesi Postdoctoral Fellowship 2025
  • Pathogen Readiness Platform for CERIC-ERIC
  • Next Generation EU
  • Università degli Studi di Napoli Federico II

Zitieren

APA

Kalligosfyri, P. M., Miller, C., Cinti, S., & Patel, B. A. (2025). 3D printed electrode-microwell system: a novel electrochemical platform for miRNA detection. Microchimica Acta, 192(5). https://doi.org/10.1007/s00604-025-07190-1

Vancouver

Kalligosfyri PM, Miller C, Cinti S, Patel BA. 3D printed electrode-microwell system: a novel electrochemical platform for miRNA detection. Microchimica Acta. 2025;192(5). doi:10.1007/s00604-025-07190-1

BibTeX
@article{Kalligosfyri2025,
  author = {Kalligosfyri, Panagiota M and Miller, Chloe and Cinti, Stefano and Patel, Bhavik Anil},
  title = {3D printed electrode-microwell system: a novel electrochemical platform for miRNA detection},
  journal = {Microchimica Acta},
  year = {2025},
  volume = {192},
  number = {5},
  doi = {10.1007/s00604-025-07190-1}
}
Kostenlos starten →