EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

A magnetic nanoparticle-based microfluidic device fabricated using a 3D-printed mould for separation of Escherichia coli from blood

Agnieszka Jóskowiak, Catarina L Nogueira, Susana P Costa, Alexandra P Cunha, Paulo P Freitas, Carla M Carvalho

Microchimica Acta · 2023

DOI: 10.1007/s00604-023-05924-7 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Microchimica Acta, 2023. Verfasst von Agnieszka Jóskowiak und 5 weiteren Autor:innen. Beteiligte Einrichtung: Centre of Biological Engineering, University of Minho, Campus de Gualtar, 4710-057, Braga, Portugal. Hauptthemen laut MEDLINE: Magnetite Nanoparticles, Sepsis. Die Arbeit wurde bisher 20-mal zitiert (Crossref) und nennt 35 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: FCT, European Regional Development Fund, INL - International Iberian Nanotechnology Laboratory.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Herein, A microfluidic device is described, produced with a 3D-printed master mould that rapidly separates and concentrates Escherichia coli directly from whole blood samples, enabling a reduction in the turnaround time of bloodstream infections (BSIs) diagnosis. Moreover, it promotes the cleansing of the blood samples whose complexity frequently hampers bacterial detection. The device comprises a serpentine mixing channel with two inlets, one for blood samples (spiked with bacteria) and the other for magnetic nanoparticles (MNPs) functionalized with a (bacterio)phage receptor-binding protein (RBP) with high specificity for E . coli . After the magnetic labelling of bacteria throughout the serpentine, the microchannel ends with a trapping reservoir where bacteria-MNPs conjugates are concentrated using a permanent magnet. The optimized sample preparation device successfully recovered E . coli (on average, 66%) from tenfold diluted blood spiked within a wide range of bacterial load (10 2 CFU to 10 7 CFU mL −1 ). The non-specific trapping, tested with Staphylococcus aureus , was at a negligible level of 12%. The assay was performed in 30 min directly from diluted blood thus presenting an advantage over the conventional enrichment in blood cultures (BCs). The device is simple and cheap to fabricate and can be tailored for multiple bacterial separation from complex clinical samples by using RBPs targeting different species. Moreover, the possibility to integrate a biosensing element to detect bacteria on-site can provide a reliable, fast, and cost-effective point-of-care device. Graphical abstract

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Magnetite NanoparticlesSepsisHumansEscherichia coliLab-On-A-Chip DevicesPrinting, Three-Dimensional

Stichwörter der Autor:innen

3D-printedBacteriophage receptor binding protein (RBP)BloodEscherichia coliMagnetic nanoparticlesMicrofluidic

Substanzen

Magnetite Nanoparticles

Autor:innen und Institutionen

  • Centre of Biological Engineering, University of Minho, Campus de Gualtar, 4710-057, Braga, Portugal.
  • LABBELS -Associate Laboratory, Braga and Guimarães, Portugal.
  • International Iberian Nanotechnology Laboratory, Av. Mestre José Veiga S/N, 4715-330, Braga, Portugal.
  • Instituto de Engenharia de Sistemas e Computadores - Microsistemas e Nanotecnologias (INESC MN) and IN - Institute of Nanoscience and Nanotechnolnology, Rua Alves Redol, 9, 1000-029, Lisbon, Portugal.
  • International Iberian Nanotechnology Laboratory, Av. Mestre José Veiga S/N, 4715-330, Braga, Portugal. carla.carvalho@inl.int.

Förderung

  • FCT
  • European Regional Development Fund
  • INL - International Iberian Nanotechnology Laboratory

Zitieren

APA

Jóskowiak, A., Nogueira, C. L., Costa, S. P., Cunha, A. P., Freitas, P. P., & Carvalho, C. M. (2023). A magnetic nanoparticle-based microfluidic device fabricated using a 3D-printed mould for separation of Escherichia coli from blood. Microchimica Acta. https://doi.org/10.1007/s00604-023-05924-7

Vancouver

Jóskowiak A, Nogueira CL, Costa SP, Cunha AP, Freitas PP, Carvalho CM. A magnetic nanoparticle-based microfluidic device fabricated using a 3D-printed mould for separation of Escherichia coli from blood. Microchimica Acta. 2023. doi:10.1007/s00604-023-05924-7

BibTeX
@article{Jskowiak2023,
  author = {Jóskowiak, Agnieszka and Nogueira, Catarina L and Costa, Susana P and Cunha, Alexandra P and Freitas, Paulo P and Carvalho, Carla M},
  title = {A magnetic nanoparticle-based microfluidic device fabricated using a 3D-printed mould for separation of Escherichia coli from blood},
  journal = {Microchimica Acta},
  year = {2023},
  doi = {10.1007/s00604-023-05924-7}
}
Kostenlos starten →