EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Quantitative Analysis and 3D Visualization of Crack Behavior in 3D-Printed Rock-Like Specimens with Single Flaw Using In-Situ Micro-CT Imaging

Yulong Shao, Jingwei Yang, Jineon Kim, Seyedahmad Mehrishal, Jae-Joon Song

Rock Mechanics and Rock Engineering · 2024-09 · 57 (9) · 7271-7291

DOI: 10.1007/s00603-024-03902-w ↗

Kurz gefasst

Fachartikel in der Zeitschrift Rock Mechanics and Rock Engineering, online erschienen am 05.05.2024. Verfasst von Yulong Shao und 4 weiteren Autor:innen. Die Arbeit wurde bisher 35-mal zitiert (Crossref) und nennt 68 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Korea Institute of Energy Technology Evaluation and Planning, Ministry of Trade, Industry, and Energy of the Korean Government, Seoul National University.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

3D printing technology allows for precise control of preparing complex geometries and internal defects in printed rock analogs, while in-situ Micro-CT imaging enables real-time observation of crack behavior. The combination of these technologies offers a new research approach for studying rock crack behavior. In this study, 3D-printed rock-like specimens containing a pre-existing flaw were prepared using a gypsum powder-based 3D printer. An advanced in-situ Micro-CT system equipped with a loading device was used to quantitatively and visually investigate the crack behavior in 3D-printed specimens under uniaxial compression testing. 2D CT images obtained from in-situ compression testing at different deformations could be used to reconstruct a 3D model and visually identify the crack patterns of the extracted cracks in 3D-printed specimens. The initiation angle of cracks, volume of the pre-existing flaw, volume of newly formed cracks, and damage value with respect to strains were analyzed to quantitatively investigate crack behavior. The results indicated that within the 3D-printed specimens, tensile cracks were first initiated near the internal flaw, followed by the occurrence of shear cracks or tensile-shear mixed cracks at the flaw tips. Additionally, there was a negative linear correlation between the initiation angle of newly formed cracks and the initial flaw angle. For flaw angles in the range of 0° ≤ α ≤ 45°, a higher number of newly formed cracks were observed in the 3D-printed specimens, and the rates of increase in crack volume and damage values with strain were faster. However, for flaw angles in the range of 45° < α ≤ 90°, the results showed the opposite trend. Furthermore, through comparison with the crack behavior of natural rocks containing a single flaw, it was found that the failure modes and crack behavior of the 3D-printed specimens exhibit certain similarities with natural rocks.

Förderung

  • Korea Institute of Energy Technology Evaluation and Planning
  • Ministry of Trade, Industry, and Energy of the Korean Government
  • Seoul National University

Zitieren

APA

Shao, Y., Yang, J., Kim, J., Mehrishal, S., & Song, J. (2024). Quantitative Analysis and 3D Visualization of Crack Behavior in 3D-Printed Rock-Like Specimens with Single Flaw Using In-Situ Micro-CT Imaging. Rock Mechanics and Rock Engineering, 57(9), 7271-7291. https://doi.org/10.1007/s00603-024-03902-w

Vancouver

Shao Y, Yang J, Kim J, Mehrishal S, Song J. Quantitative Analysis and 3D Visualization of Crack Behavior in 3D-Printed Rock-Like Specimens with Single Flaw Using In-Situ Micro-CT Imaging. Rock Mechanics and Rock Engineering. 2024;57(9):7271-7291. doi:10.1007/s00603-024-03902-w

BibTeX
@article{Shao2024,
  author = {Shao, Yulong and Yang, Jingwei and Kim, Jineon and Mehrishal, Seyedahmad and Song, Jae-Joon},
  title = {Quantitative Analysis and 3D Visualization of Crack Behavior in 3D-Printed Rock-Like Specimens with Single Flaw Using In-Situ Micro-CT Imaging},
  journal = {Rock Mechanics and Rock Engineering},
  year = {2024},
  volume = {57},
  number = {9},
  pages = {7271--7291},
  doi = {10.1007/s00603-024-03902-w}
}
Kostenlos starten →