EUVIMEDEUVIMED entdecken
Crossref

Adhesive solid-state fermentation producing Aspergillus niger conidia on stainless-steel dixon ring supports

Xiaoran Zhang iD, Dan Liu, Peng Wan

Bioprocess and Biosystems Engineering · 2024

DOI: 10.1007/s00449-024-03071-8 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Bioprocess and Biosystems Engineering, 2024. Verfasst von Xiaoran Zhang und 2 weiteren Autor:innen. Beteiligte Einrichtung: College of Chemistry and Chemical Engineering, Yan'an University, Yan'an, 716000, Shaanxi, China. zhangxiaoran@yau.edu.cn. Hauptthemen laut MEDLINE: Aspergillus niger, Stainless Steel, Spores, Fungal. Die Arbeit wurde bisher 1-mal zitiert (Crossref) und nennt 33 Literaturangaben. Gefördert von: National Natural Science Foundation of China, Yan'an University.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

An adhesive solid-state fermentation (adSSF) mode was developed to produce Aspergillus niger conidia, which used a stainless-steel Dixon ring as the support and water-retaining adhesive to load nutritional media on its surface. To obtain high conidia yields, the components of the water-retaining adhesive were screened, optimized by single-factor optimization and response surface methodology, and the optimal dosages of the main components were: wheat bran powder 0.023 g·cm-3bed, cassava starch 0.0022 g·cm-3bed, and xanthan gum 0.0083 g·cm-3bed. The experimentally tested conidia yield was 4.2-fold that without water-retaining adhesive but was 3.7% lower than the maximum yield predicted by the model. The observed double-side growth of A. niger on the Dixon ring supports improved space utilization of the fermentation bed, and the void fraction can increase with the shrinkage of the gel layer. In 1.6 L tray reactors with three-point online temperature monitoring, the inner-bed temperature of adSSF was at most 4 °C lower than the adsorbed carrier solid-state fermentation (ACSSF) mode, and the conidia yield was 1.68 × 108 conidia.cm-3bed, 61.5% higher than that of the ACSSF bed at the same time, but when the fermentation time was extended to 168 h, the conidia yield of the adSSF bed and ACSSF bed were close to each other. The results revealed that the high voidage of the adSSF bed was the main reason for low bed temperature, which can benefit the inner-bed natural convection and water evaporation.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Aspergillus nigerStainless SteelSpores, FungalFermentationBioreactors

Stichwörter der Autor:innen

AdhesionConidiaDixon ringSolid-state fermentationSupport

Substanzen

Stainless Steel

Autor:innen und Institutionen

  • College of Chemistry and Chemical Engineering, Yan'an University, Yan'an, 716000, Shaanxi, China. zhangxiaoran@yau.edu.cn.
  • Shaanxi Key Laboratory of Chemical Reaction Engineering, Yan'an University, Yan'an, 716000, Shaanxi, China. zhangxiaoran@yau.edu.cn.
  • College of Chemistry and Chemical Engineering, Yan'an University, Yan'an, 716000, Shaanxi, China.
  • Shaanxi Key Laboratory of Chemical Reaction Engineering, Yan'an University, Yan'an, 716000, Shaanxi, China.

ORCID-Profile: Xiaoran Zhang

Förderung

  • National Natural Science Foundation of China
  • Yan'an University

Zitieren

APA

Zhang, X., Liu, D., & Wan, P. (2024). Adhesive solid-state fermentation producing Aspergillus niger conidia on stainless-steel dixon ring supports. Bioprocess and Biosystems Engineering. https://doi.org/10.1007/s00449-024-03071-8

Vancouver

Zhang X, Liu D, Wan P. Adhesive solid-state fermentation producing Aspergillus niger conidia on stainless-steel dixon ring supports. Bioprocess and Biosystems Engineering. 2024. doi:10.1007/s00449-024-03071-8

BibTeX
@article{Zhang2024,
  author = {Zhang, Xiaoran and Liu, Dan and Wan, Peng},
  title = {Adhesive solid-state fermentation producing Aspergillus niger conidia on stainless-steel dixon ring supports},
  journal = {Bioprocess and Biosystems Engineering},
  year = {2024},
  doi = {10.1007/s00449-024-03071-8}
}
Kostenlos starten →