Effect of case-specific 3D-printed models on surgical performance in cadaveric dissection—a randomized controlled trial
European Archives of Oto-Rhino-Laryngology · 2026-06 · 283 (6) · 3671-3679
DOI: 10.1007/s00405-026-10099-x ↗Kurz gefasst
Randomisierte kontrollierte Studie in der Zeitschrift European Archives of Oto-Rhino-Laryngology, online erschienen am 09.03.2026. Verfasst von Adam Omari und 6 weiteren Autor:innen. Beteiligte Einrichtung: Copenhagen Hearing and Balance Center, Department of Otolaryngology-Head & Neck Surgery, Rigshospitalet, Copenhagen University Hospital, Copenhagen, …. Hauptthemen laut MEDLINE: Cadaver, Clinical Competence, Mastoidectomy, Otolaryngology. Die Arbeit wurde bisher 5-mal zitiert (Crossref) und nennt 42 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: National Hospital.
Abstract (Originalsprache)
PURPOSE: To investigate if training with case-specific 3D-printed temporal bone (TB) models improves trainees’ mastoidectomy performance in cadaveric dissection compared with training on a standard, generic-anatomy 3D-printed TB model. METHODS: In this randomized controlled trial, 22 novice ORL residents performed a cadaveric mastoidectomy with posterior tympanotomy after training two procedures either on 3D-printed TB models of their specific cadaveric bone (CM, n = 11), or on 3D-printed TB with generic anatomy (GM, n = 11). Blinded experts assessed final-product performance using a modified Welling Scale. Secondary outcomes included correlation between performance on 3D-printed models and cadavers, questionnaires on model quality, and usefulness for planning. RESULTS: On their first 3D-printed model, the CM group performed better than the GM group (13.1 vs. 10.9 points; p < 0.01). In their second 3D-printed procedure, scores were similar (15.8 vs. 15.7; p = 0.9) as both groups improved significantly from the first to the second procedure (p < 0.001). In subsequent cadaver dissection, the CM group scored lower than the GM group (13.2 vs. 14.4; p < 0.001). Correlation between performance on 3D-printed models and cadavers was not significant in the CM group (r = 0.45; p = 0.16) but very strong in the GM group (r = 0.77; p < 0.01). Questionnaire responses indicated high perceived realism and educational value in both groups. CONCLUSION: Training with case-specific 3D-printed TB models did not benefit or correlate with cadaveric mastoidectomy performance in novice residents. This supports the use of generic-anatomy, educational 3D-printed TB models in the early training stages and highlights the importance of aligning simulation fidelity with learner experience. TRIAL REGISTRATION: Not applicable.
Schlagwörter
MeSH-Schlagwörter (MEDLINE)
Stichwörter der Autor:innen
Autor:innen und Institutionen
- Copenhagen Hearing and Balance Center, Department of Otolaryngology-Head & Neck Surgery, Rigshospitalet, Copenhagen University Hospital, Copenhagen, Denmark. adam.omari@hotmail.com.
- Institute for Cellular and Molecular Medicine (ICMM), Faculty of Health and Medical Sciences, University of Copenhagen, Copenhagen, Denmark. adam.omari@hotmail.com.
- Center for HR & Education, Copenhagen Academy for Medical Education and Simulation (CAMES), RegionH, Copenhagen, Denmark. adam.omari@hotmail.com.
- Copenhagen Hearing and Balance Center, Department of Otolaryngology-Head & Neck Surgery, Rigshospitalet, Copenhagen University Hospital, Copenhagen, Denmark.
- Center for HR & Education, Copenhagen Academy for Medical Education and Simulation (CAMES), RegionH, Copenhagen, Denmark.
- Dept. of Clinical Medicine (ICM), Faculty of Health and Medical Sciences, University of Copenhagen, Copenhagen, Denmark.
Förderung
- National Hospital
Zitieren
APA
Omari, A., Nøhr, A., Suleiman, E., Cayé-Thomasen, P., Sørensen, M. S., Frithioff, A., & Andersen, S. A. W. (2026). Effect of case-specific 3D-printed models on surgical performance in cadaveric dissection—a randomized controlled trial. European Archives of Oto-Rhino-Laryngology, 283(6), 3671-3679. https://doi.org/10.1007/s00405-026-10099-x
Vancouver
Omari A, Nøhr A, Suleiman E, Cayé-Thomasen P, Sørensen MS, Frithioff A, et al. Effect of case-specific 3D-printed models on surgical performance in cadaveric dissection—a randomized controlled trial. European Archives of Oto-Rhino-Laryngology. 2026;283(6):3671-3679. doi:10.1007/s00405-026-10099-x
BibTeX
@article{Omari2026,
author = {Omari, Adam and Nøhr, Anders and Suleiman, Elissa and Cayé-Thomasen, Per and Sørensen, Mads Sølvsten and Frithioff, Andreas and Andersen, Steven Arild Wuyts},
title = {Effect of case-specific 3D-printed models on surgical performance in cadaveric dissection—a randomized controlled trial},
journal = {European Archives of Oto-Rhino-Laryngology},
year = {2026},
volume = {283},
number = {6},
pages = {3671--3679},
doi = {10.1007/s00405-026-10099-x}
}
EUVIMED