Short-term results of minimally invasive surgery using a 3D-printed guide for the treatment of hallux valgus
Archives of Orthopaedic and Trauma Surgery · 2025
DOI: 10.1007/s00402-025-05830-y ↗Kurz gefasst
Fachartikel in der Zeitschrift Archives of Orthopaedic and Trauma Surgery, 2025. Verfasst von Songbai Wang und 5 weiteren Autor:innen. Beteiligte Einrichtung: Shenzhen Pingle Orthopedics Hospital (Shenzhen Pingshan Traditional Chinese Medicine Hospital), Shenzhen, China. Hauptthemen laut MEDLINE: Hallux Valgus, Minimally Invasive Surgical Procedures, Printing, Three-Dimensional, Osteotomy. Die Arbeit nennt 27 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY-NC-ND 4.0). Gefördert von: Science and Technology Planning Project of Shenzen Municipality.
Abstract (Originalsprache)
INTRODUCTION: Minimally invasive surgery (MIS) is often used to treat hallux valgus deformities, as it is associated with few wound complications and shorter recovery times. Minimally invasive chevron osteotomy and Akin osteotomy (MICA) is a common minimally invasive treatment for HV. However, effective correction of hallux valgus and precise screw placement during MIS are difficult. The aim of this study was to introduce and evaluate the clinical and radiographic effectiveness of a novel MIS technique involving the use of a 3D-printed guide for hallux valgus. MATERIALS AND METHODS: We retrospectively studied the results of MIS with a 3D-printed guide plate for symptomatic hallux valgus from May 2022 to December 2023. The preoperative and postoperative hallux valgus angle (HVA), intermetatarsal angle (IMA), distal metatarsal articular angle (DMAA), first metatarsal pronation angle (M1PA), tibial sesamoid position (TSP), forefoot width, visual analogue scale (VAS) score, AOFAS Hallux MTP-IP score, and the number of intraoperative fluoroscopy were measured. RESULTS: A total of 22 feet in 19 patients were included in the study. There were 15 women and 4 men with an average age of 38.0 y (range 16-61). The preoperative HVA, IMA, DMAA and M1PA were 30.3 ± 10.7°, 13.9 ± 2.8°, 8.3 ± 2.9° and 16.3 ± 6.5°, respectively. The postoperative HVA, IMA, DMAA and M1PA were 10.7 ± 4.1°, 5.7 ± 1.8°, 2.3 ± 1.7° and 3.5 ± 2.1°, respectively. The forefoot width decreased from 92.1 ± 5.5 mm to 85.6 ± 5.4 mm on average. The VAS and TSP ranged from 4.4 ± 0.9 and 4.9 ± 0.8 to 0.3 ± 0.6 and 2.0 ± 1.1, respectively. The AOFAS Hallux MTP-IP scores improved from 59.1 ± 10.7 to 94.8 ± 5.7 on average. The average number of fluoroscopy shots during operation were 34 times (range 30 to 38). CONCLUSIONS: A 3D printed guide technique can be beneficial for precise positioning of the first metatarsal head, enhancing the accuracy of screw placement, and reducing radiation exposure.
Schlagwörter
MeSH-Schlagwörter (MEDLINE)
Stichwörter der Autor:innen
Autor:innen und Institutionen
- Shenzhen Pingle Orthopedics Hospital (Shenzhen Pingshan Traditional Chinese Medicine Hospital), Shenzhen, China.
- Shenzhen Pingle Orthopedics Hospital (Shenzhen Pingshan Traditional Chinese Medicine Hospital), Shenzhen, China. wsb76@163.com.
Förderung
- Science and Technology Planning Project of Shenzen Municipality
Zitieren
APA
Wang, S., Zhu, Y., Liu, J., Zheng, G., He, G., & Bai, Y. (2025). Short-term results of minimally invasive surgery using a 3D-printed guide for the treatment of hallux valgus. Archives of Orthopaedic and Trauma Surgery. https://doi.org/10.1007/s00402-025-05830-y
Vancouver
Wang S, Zhu Y, Liu J, Zheng G, He G, Bai Y. Short-term results of minimally invasive surgery using a 3D-printed guide for the treatment of hallux valgus. Archives of Orthopaedic and Trauma Surgery. 2025. doi:10.1007/s00402-025-05830-y
BibTeX
@article{Wang2025,
author = {Wang, Songbai and Zhu, Yuanbin and Liu, Jian and Zheng, Guofan and He, Gansheng and Bai, Yunbo},
title = {Short-term results of minimally invasive surgery using a 3D-printed guide for the treatment of hallux valgus},
journal = {Archives of Orthopaedic and Trauma Surgery},
year = {2025},
doi = {10.1007/s00402-025-05830-y}
}
EUVIMED