EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Patient specific instrumentation in ACL reconstruction: a proof-of-concept cadaver experiment assessing drilling accuracy when using 3D printed guides

Mark J M Zee, Peter A J Pijpker, Joep Kraeima, Alain R Viddeleer, Ronald L Diercks

Archives of Orthopaedic and Trauma Surgery · 2023

DOI: 10.1007/s00402-023-05072-w ↗

Kurz gefasst

Fachartikel in der Zeitschrift Archives of Orthopaedic and Trauma Surgery, 2023. Verfasst von Mark J M Zee und 4 weiteren Autor:innen. Beteiligte Einrichtung: Department of Orthopedic Surgery, University of Groningen, University Medical Centre Groningen, Hanzeplein 1, PO Box 30.001, 9700RB, Groningen, The N…. Hauptthemen laut MEDLINE: Anterior Cruciate Ligament, Anterior Cruciate Ligament Reconstruction. Die Arbeit wurde bisher 4-mal zitiert (Crossref) und nennt 29 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Samenwerkingsverband Noord-Nederland.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Introduction

Accurate positioning of the femoral tunnel in ACL reconstruction is of the utmost importance to reduce the risk of graft failure. Limited visibility during arthroscopy and a wide anatomical variance attribute to femoral tunnel malposition using conventional surgical techniques. The purpose of this study was to determine whether a patient specific 3D printed surgical guide allows for in vitro femoral tunnel positioning within 2 mm of the planned tunnel position. Materials and Methods A patient specific guide for femoral tunnel positioning in ACL reconstruction was created for four human cadaveric knee specimens based on routine clinical MRI data. Fitting properties were judged by two orthopedic surgeons. MRI scanning was performed both pre- and post-procedure. The planned tunnel endpoint was compared to the actual drilled femoral tunnel.

Results

This patient specific 3D printed guide showed a mean deviation of 5.0 mm from the center of the planned femoral ACL origin.

Conclusion

In search to improve accuracy and consistency of femoral tunnel positioning in ACL reconstruction, the use of a patient specific 3D printed surgical guide is a viable option to explore further. The results are comparable to those of conventional techniques; however, further design improvements are necessary to improve accuracy and enhance reproducibility.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Anterior Cruciate LigamentAnterior Cruciate Ligament ReconstructionHumansTibiaReproducibility of ResultsKnee JointFemurCadaverPrinting, Three-Dimensional

Stichwörter der Autor:innen

ACL reconstructionAnatomicFemoral tunnelPatient specific instrument

Autor:innen und Institutionen

  • Department of Orthopedic Surgery, University of Groningen, University Medical Centre Groningen, Hanzeplein 1, PO Box 30.001, 9700RB, Groningen, The Netherlands. m.j.m.zee@umcg.nl.
  • 3D Lab, Department of Orthopedic Surgery, University of Groningen, University Medical Centre Groningen, Hanzeplein 1, PO Box 30.001, 9700RB, Groningen, The Netherlands.
  • 3D Lab, Department of Oral and Maxillofacial Surgery, University of Groningen, University Medical Centre Groningen, Hanzeplein 1, PO Box 30.001, 9700RB, Groningen, The Netherlands.
  • Medical Imaging Center, Department of Radiology, University of Groningen, University Medical Centre Groningen, Hanzeplein 1, PO Box 30.001, 9700RB, Groningen, The Netherlands.
  • Department of Orthopedic Surgery, University of Groningen, University Medical Centre Groningen, Hanzeplein 1, PO Box 30.001, 9700RB, Groningen, The Netherlands.

Förderung

  • Samenwerkingsverband Noord-Nederland

Zitieren

APA

Zee, M. J. M., Pijpker, P. A. J., Kraeima, J., Viddeleer, A. R., & Diercks, R. L. (2023). Patient specific instrumentation in ACL reconstruction: a proof-of-concept cadaver experiment assessing drilling accuracy when using 3D printed guides. Archives of Orthopaedic and Trauma Surgery. https://doi.org/10.1007/s00402-023-05072-w

Vancouver

Zee MJM, Pijpker PAJ, Kraeima J, Viddeleer AR, Diercks RL. Patient specific instrumentation in ACL reconstruction: a proof-of-concept cadaver experiment assessing drilling accuracy when using 3D printed guides. Archives of Orthopaedic and Trauma Surgery. 2023. doi:10.1007/s00402-023-05072-w

BibTeX
@article{Zee2023,
  author = {Zee, Mark J M and Pijpker, Peter A J and Kraeima, Joep and Viddeleer, Alain R and Diercks, Ronald L},
  title = {Patient specific instrumentation in ACL reconstruction: a proof-of-concept cadaver experiment assessing drilling accuracy when using 3D printed guides},
  journal = {Archives of Orthopaedic and Trauma Surgery},
  year = {2023},
  doi = {10.1007/s00402-023-05072-w}
}
Kostenlos starten →