EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

High aspect ratio diamond nanosecond laser machining

Natalie C Golota iD, David Preiss, Zachary P Fredin, Prashant Patil, Daniel P Banks, Salima Bahri, Robert G Griffin iD, Neil Gershenfeld

Applied Physics A · 2023-07 · 129 (7)

DOI: 10.1007/s00339-023-06755-2 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Applied Physics A, online erschienen am 15.06.2023. Verfasst von Natalie C Golota und 7 weiteren Autor:innen. Beteiligte Einrichtung: Department of Chemistry, Massachusetts Institute of Technology, Cambridge, MA 02139 USA. Die Arbeit wurde bisher 19-mal zitiert (Crossref) und nennt 53 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: NIA NIH HHS, NIGMS NIH HHS, National Institutes of Health.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Laser processing of diamond has become an important technique for fabricating next generation microelectronic and quantum devices. However, the realization of low taper, high aspect ratio structures in diamond remains a challenge. We demonstrate the effects of pulse energy, pulse number and irradiation profile on the achievable aspect ratio with 532 nm nanosecond laser machining. Strong and gentle ablation regimes were observed using percussion hole drilling of type Ib HPHT diamond. Under percussion hole drilling a maximum aspect ratio of 22:1 was achieved with 10,000 pulses. To reach aspect ratios on average 40:1 and up to 66:1, rotary assisted drilling was employed using > 2 M pulse accumulations. We additionally demonstrate methods of obtaining 0.1° taper angles via ramped pulse energy machining in 10:1 aspect ratio tubes. Finally, effects of laser induced damage are studied using confocal Raman spectroscopy with observation of up to 36% increase in tensile strain following strong laser irradiation. However, we report that upon application of 600 °C heat treatment, induced strain is reduced by up to ~ 50% with considerable homogenization of observed strain.

Schlagwörter

Stichwörter der Autor:innen

Diamond laser machiningFundamentals of laser processingLaser ablationLaser induced damage analysisNanosecond laser machining

Autor:innen und Institutionen

  • Department of Chemistry, Massachusetts Institute of Technology, Cambridge, MA 02139 USA.
  • Francis Bitter Magnet Laboratory, Massachusetts Institute of Technology, Cambridge, MA 02139 USA.
  • Center for Bits and Atoms, Massachusetts Institute of Technology, Cambridge, MA 02139 USA.

ORCID-Profile: Natalie C Golota, Robert G Griffin

Förderung

  • NIA NIH HHS
  • NIGMS NIH HHS
  • National Institutes of Health
  • National Insitutes of Health
  • National Science Foundation
  • Massachusetts Institute of Technology

Zitieren

APA

Golota, N. C., Preiss, D., Fredin, Z. P., Patil, P., Banks, D. P., Bahri, S., Griffin, R. G., & Gershenfeld, N. (2023). High aspect ratio diamond nanosecond laser machining. Applied Physics A, 129(7). https://doi.org/10.1007/s00339-023-06755-2

Vancouver

Golota NC, Preiss D, Fredin ZP, Patil P, Banks DP, Bahri S, et al. High aspect ratio diamond nanosecond laser machining. Applied Physics A. 2023;129(7). doi:10.1007/s00339-023-06755-2

BibTeX
@article{Golota2023,
  author = {Golota, Natalie C and Preiss, David and Fredin, Zachary P and Patil, Prashant and Banks, Daniel P and Bahri, Salima and Griffin, Robert G and Gershenfeld, Neil},
  title = {High aspect ratio diamond nanosecond laser machining},
  journal = {Applied Physics A},
  year = {2023},
  volume = {129},
  number = {7},
  doi = {10.1007/s00339-023-06755-2}
}
Kostenlos starten →