Effectiveness of three-dimensional printed lumbar spine-model-based training for epidural anesthesia in novice anesthesiology residents
Surgical and Radiologic Anatomy · 30.06.2026 · 48 (1)
DOI: 10.1007/s00276-026-03933-8 ↗Kurz gefasst
Randomisierte kontrollierte Studie in der Zeitschrift Surgical and Radiologic Anatomy, online erschienen am 30.06.2026. Verfasst von Nezih Sertoz und 4 weiteren Autor:innen. Beteiligte Einrichtung: Department of Anesthesia and Reanimation, Faculty of Medicine, Ege University, Izmir, Turkey. Hauptthemen laut MEDLINE: Internship and Residency, Anesthesiology, Anesthesia, Epidural, Models, Anatomic. Die Arbeit nennt 42 Literaturangaben.
Abstract (Originalsprache)
BACKGROUND: Epidural procedures have a steep learning curve and may raise patient-safety concerns during early anesthesiology training. We evaluated whether a low-cost, three-dimensional (3D) simulation model improves early procedural success and efficiency in novice trainees. METHODS: In this prospective randomized controlled study, 36 anesthesia residents were randomized into two groups. Group A received hands-on training on a 3D simulation model plus audiovisual teaching, whereas Group B received audiovisual teaching only. Performance was assessed at baseline (0 h), 3 h, and 6 h using procedural success, a checklist score, and a global rating scale; procedure time was recorded. RESULTS: Baseline success was comparable between groups. At 3 h and 6 h, Group A demonstrated a marked improvement, reaching a success rate of 94.4% at 6 h compared with 50.0% in Group B. Checklist scores did not differ at baseline (p = 0.888) but were significantly higher in Group A at 3 h and 6 h (both p < 0.001). Procedure time decreased significantly in Group A (from 149 ± 24 s to 107 ± 26 s, p < 0.001) versus a limited reduction in Group B (from 148 ± 26 s to 142 ± 22 s, p = 0.001). The model was inexpensive and feasible to produce (~ 6 h printing time; total cost ~$11.50/model). CONCLUSION: Low-cost 3D model-assisted training improved short-term simulator-based epidural performance, checklist scores, GRS scores, and procedural efficiency among novice anesthesiology residents. These findings support the use of 3D printed models as an accessible hands-on adjunct to conventional audiovisual epidural anesthesia training. Further studies are needed to determine whether these improvements translate into long-term retention, clinical performance and patient outcomes.
Schlagwörter
MeSH-Schlagwörter (MEDLINE)
Stichwörter der Autor:innen
Autor:innen und Institutionen
- Department of Anesthesia and Reanimation, Faculty of Medicine, Ege University, Izmir, Turkey.
- Department of Anatomy, Faculty of Medicine, Ege University, Izmir, Turkey.
- Department of Anatomy, Faculty of Medicine, Ege University, Izmir, Turkey. fgovsa@yahoo.com.
ORCID-Profile: Figen Govsa
Zitieren
APA
Sertoz, N., Sahutoglu, C., Ozgul, K. K., Ozer, M. A., & Govsa, F. (2026). Effectiveness of three-dimensional printed lumbar spine-model-based training for epidural anesthesia in novice anesthesiology residents. Surgical and Radiologic Anatomy, 48(1). https://doi.org/10.1007/s00276-026-03933-8
Vancouver
Sertoz N, Sahutoglu C, Ozgul KK, Ozer MA, Govsa F. Effectiveness of three-dimensional printed lumbar spine-model-based training for epidural anesthesia in novice anesthesiology residents. Surgical and Radiologic Anatomy. 2026;48(1). doi:10.1007/s00276-026-03933-8
BibTeX
@article{Sertoz2026,
author = {Sertoz, Nezih and Sahutoglu, Cengiz and Ozgul, Kazim Koray and Ozer, Mehmet Asim and Govsa, Figen},
title = {Effectiveness of three-dimensional printed lumbar spine-model-based training for epidural anesthesia in novice anesthesiology residents},
journal = {Surgical and Radiologic Anatomy},
year = {2026},
volume = {48},
number = {1},
doi = {10.1007/s00276-026-03933-8}
}
EUVIMED