EUVIMEDEUVIMED entdecken
Crossref

Research and application discussion of cranial bone model preparation method based on three-dimensional reconstruction and 3D printing technology

Jing Peng, Wenjie Guo, Deqin Yang, Guohui Yang, Yanhong Shu, Ying Li, Libing Rao, Penghui Yu, Li Li

Surgical and Radiologic Anatomy · 2024

DOI: 10.1007/s00276-024-03455-1 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Surgical and Radiologic Anatomy, 2024. Verfasst von Jing Peng und 8 weiteren Autor:innen. Beteiligte Einrichtung: Hunan University of Medicine, Huaihua, 418000, Hunan Province, China. Hauptthemen laut MEDLINE: Printing, Three-Dimensional, Skull, Models, Anatomic, Imaging, Three-Dimensional. Die Arbeit wurde bisher 2-mal zitiert (Crossref) und nennt 25 Literaturangaben. Gefördert von: Scientific Research Fund of Hunan Provincial Education Department, Research Project on Teaching Reform of Ordinary Higher Education Institutions in Hunan Province, Hunan Province Social Science Outcome Review Committee Project.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

PURPOSE: The aim of this study was to find an alternative method to meet traditional human anatomy teaching and clinical needs in order to solve the problem of cranial specimen attrition and specimen resource shortage due to long-term use. METHODS: We performed a computed tomography (CT) scan of a well-preserved male cranial specimen and used Mimics 19.0 software for 3D reconstruction and cranial block separation. Subsequently, we compared the recognition ability of the processed cranial digital model with that of the 3D body digital model and used 3D printing to create the cranial model and compare it with the physical specimen. RESULTS: Twenty-two cranial bone block models were obtained, excluding the hyoid bone. Their 3D reconstructed digital models had better bony landmark recognition than the 3D body human digital models, and the differences between the 3D printed models and the physical specimens were minimal. In addition, only one stereolithography (STL) file was required to produce the cranial models, which facilitates repetitive printing at any time. CONCLUSION: By isolating cranial bone blocks through 3D reconstruction techniques and preparing high-quality cranial models in combination with 3D printing techniques, this study solves the problem of shortage of cranial teaching specimens for the sustainable development of clinical and medical schools.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Printing, Three-DimensionalSkullModels, AnatomicImaging, Three-DimensionalTomography, X-Ray ComputedHumansMaleStereolithographyCadaverSoftware

Stichwörter der Autor:innen

3D Printing3D ReconstructionCranial separationCranial specimensTeaching resource

Autor:innen und Institutionen

  • Hunan University of Medicine, Huaihua, 418000, Hunan Province, China.
  • Huaihua Key Laboratory of Digital Anatomy and 3D Printing for Clinical Translational Research, Huaihua, 418000, Hunan Province, China.
  • Innovation and Entrepreneurship Education Center for Clinical Translational Application of Digital Anatomy and 3D Printing Technology in General Colleges and Universities in Hunan Province, Huaihua, 418000, Hunan Provin…
  • Hunan University of Medicine, Huaihua, 418000, Hunan Province, China. Phy527@126.com.
  • Huaihua Key Laboratory of Digital Anatomy and 3D Printing for Clinical Translational Research, Huaihua, 418000, Hunan Province, China. Phy527@126.com.
  • Hunan University of Medicine, Huaihua, 418000, Hunan Province, China. Lili202404@126.com.

Förderung

  • Scientific Research Fund of Hunan Provincial Education Department
  • Research Project on Teaching Reform of Ordinary Higher Education Institutions in Hunan Province
  • Hunan Province Social Science Outcome Review Committee Project
  • Huaihua Science and Technology Innovation Plan Project
  • Hunan Provincial Natural Science Foundation of China
  • Project of Key Laboratory of Digital Anatomy and 3D Printing Clinical Translational Research in Huaihua City
  • Horizontal Projects

Zitieren

APA

Peng, J., Guo, W., Yang, D., Yang, G., Shu, Y., Li, Y., Rao, L., Yu, P., & Li, L. (2024). Research and application discussion of cranial bone model preparation method based on three-dimensional reconstruction and 3D printing technology. Surgical and Radiologic Anatomy. https://doi.org/10.1007/s00276-024-03455-1

Vancouver

Peng J, Guo W, Yang D, Yang G, Shu Y, Li Y, et al. Research and application discussion of cranial bone model preparation method based on three-dimensional reconstruction and 3D printing technology. Surgical and Radiologic Anatomy. 2024. doi:10.1007/s00276-024-03455-1

BibTeX
@article{Peng2024,
  author = {Peng, Jing and Guo, Wenjie and Yang, Deqin and Yang, Guohui and Shu, Yanhong and Li, Ying and Rao, Libing and Yu, Penghui and Li, Li},
  title = {Research and application discussion of cranial bone model preparation method based on three-dimensional reconstruction and 3D printing technology},
  journal = {Surgical and Radiologic Anatomy},
  year = {2024},
  doi = {10.1007/s00276-024-03455-1}
}
Kostenlos starten →