3D Bioprinting-Based Dopamine-Coupled Flexible Material for Nasal Cartilage Repair
Aesthetic Plastic Surgery · 2024-08 · 48 (15) · 2951-2964
DOI: 10.1007/s00266-024-03982-7 ↗Kurz gefasst
Fachartikel in der Zeitschrift Aesthetic Plastic Surgery, online erschienen am 25.03.2024. Verfasst von Wendan Jia und 9 weiteren Autor:innen. Beteiligte Einrichtung: Shanxi Key Laboratory of Micro Nano Sensors & Artificial Intelligence Perception, College of Electronic Information and Optical Engineering, Taiyuan …. Hauptthemen laut MEDLINE: Printing, Three-Dimensional, Bioprinting, Tissue Scaffolds, Tissue Engineering. Die Arbeit wurde bisher 10-mal zitiert (Crossref) und nennt 44 Literaturangaben. Gefördert von: the National Natural Science Foundation of China, Shanxi Provincial Key Medical Scientific Research Project, Shanxi Provincial Basic Research Project.
Abstract (Originalsprache)
INTRODUCTION: Since 3D printing can be used to design implants according to the specific conditions of patients, it has become an emerging technology in tissue engineering and regenerative medicine. How to improve the mechanical, elastic and adhesion properties of 3D-printed photocrosslinked hydrogels is the focus of cartilage tissue repair and reconstruction research. MATERIALS AND METHODS: We established a strategy for toughening hydrogels by mixing GelMA-DOPA (GD), which is prepared by coupling dopamine (DA) with GelMA, with HAMA, bacterial cellulose (BC) to produce composite hydrogels (HB-GD). HB-GD hydrogel scaffolds were characterized in vitro by scanning electron microscopy (SEM), Young's modulus, swelling property and rheological property tests. And biocompatibility and chondrogenic ability were tested by live/dead staining, DNA quantitative analysis and immunofluorescence staining. Combined with 3D bioprinting technology, mouse chondrocytes (ADTC5) were added to form a biological chain to construct an in vitro model, and the feasibility of the model for nasal cartilage regeneration was verified by cytology evaluation. RESULTS: With the increase of GD concentration, the toughness of the composite hydrogel increased (47.0 ± 2.7 kPa (HB-5GD)-158 ± 3.2 kPa (HB-20GD)), and it had excellent swelling properties, rheological properties and printing properties. The HB-GD composite hydrogel promoted the proliferation and differentiation of ATDC5. Cells in 3D printed scaffolds had higher survival rates (> 95%) and better protein expression than the encapsulated cultures. CONCLUSION: The HB-10GD hydrogel can be made into a porous scaffold with precise shape, good internal pore structure, high mechanical strength and good swelling rate through extrusion 3D printing. NO LEVEL ASSIGNED: This journal requires that authors assign a level of evidence to each submission to which Evidence-Based Medicine rankings are applicable. This excludes Review Articles, Book Reviews, and manuscripts that concern Basic Science, Animal Studies, Cadaver Studies, and Experimental Studies. For a full description of these Evidence-Based Medicine ratings, please refer to the Table of Contents or the online Instructions to Authors www.springer.com/00266.
Schlagwörter
MeSH-Schlagwörter (MEDLINE)
Stichwörter der Autor:innen
Substanzen
Autor:innen und Institutionen
- Shanxi Key Laboratory of Micro Nano Sensors & Artificial Intelligence Perception, College of Electronic Information and Optical Engineering, Taiyuan University of Technology, Taiyuan, 030024, China.
- Key Lab of Advanced Transducers and Intelligent Control System of the Ministry of Education, Taiyuan University of Technology, Taiyuan, 030024, China.
- Shanxi-Zheda Institute of Advanced Materials and Chemical Engineering, Taiyuan, 030024, China.
- Shanxi Research Institute of 6D Artificial Intelligence Biomedical Science, Taiyuan, 030031, China.
- College of Information Science and Engineering, Hebei North University, Zhangjiakou, 075000, China.
- Shanxi Key Laboratory of Micro Nano Sensors & Artificial Intelligence Perception, College of Electronic Information and Optical Engineering, Taiyuan University of Technology, Taiyuan, 030024, China. sunboa-sang@tyut.edu…
ORCID-Profile: Shengbo Sang
Förderung
- the National Natural Science Foundation of China
- Shanxi Provincial Key Medical Scientific Research Project
- Shanxi Provincial Basic Research Project
- Scientific and Technological Innovation Programs of Higher Education Institutions in Shanxi
- Shanxi-Zheda Institute of Advanced Materials and Chemical Engineering
- the Key Research and Development Program of Shanxi Province
Zitieren
APA
Jia, W., Liu, Z., Ma, Z., Hou, P., Cao, Y., Shen, Z., Li, M., Zhang, H., Guo, X., & Sang, S. (2024). 3D Bioprinting-Based Dopamine-Coupled Flexible Material for Nasal Cartilage Repair. Aesthetic Plastic Surgery, 48(15), 2951-2964. https://doi.org/10.1007/s00266-024-03982-7
Vancouver
Jia W, Liu Z, Ma Z, Hou P, Cao Y, Shen Z, et al. 3D Bioprinting-Based Dopamine-Coupled Flexible Material for Nasal Cartilage Repair. Aesthetic Plastic Surgery. 2024;48(15):2951-2964. doi:10.1007/s00266-024-03982-7
BibTeX
@article{Jia2024,
author = {Jia, Wendan and Liu, Zixian and Ma, Zhuwei and Hou, Peiyi and Cao, Yanyan and Shen, Zhizhong and Li, Meng and Zhang, Hulin and Guo, Xing and Sang, Shengbo},
title = {3D Bioprinting-Based Dopamine-Coupled Flexible Material for Nasal Cartilage Repair},
journal = {Aesthetic Plastic Surgery},
year = {2024},
volume = {48},
number = {15},
pages = {2951--2964},
doi = {10.1007/s00266-024-03982-7}
}
EUVIMED