EUVIMEDEUVIMED entdecken
Open Access

Use of 3D printing to integrate microchip electrophoresis with amperometric detection

Major A Selemani, R Scott Martin

Analytical and Bioanalytical Chemistry · 2024-09 · 416 (21) · 4749-4758

DOI: 10.1007/s00216-024-05260-6 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Analytical and Bioanalytical Chemistry, online erschienen am 06.04.2024. Verfasst von Major A Selemani und 1 weiteren Autor:innen. Beteiligte Einrichtung: Department of Chemistry, Saint Louis University, Saint Louis, MO, USA. Die Arbeit wurde bisher 12-mal zitiert (Crossref) und nennt 54 Literaturangaben. Der Volltext ist frei in PubMed Central verfügbar. Gefördert von: NIGMS NIH HHS, National Institute of General Medical Sciences.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

This paper describes the use of PolyJet 3D printing to fabricate microchip electrophoresis devices with integrated microwire electrodes for amperometric detection. The fabrication process involves 3D printing of two separate pieces, a channel layer and an electrode layer. The channel layer is created by 3D printing on a pre-fabricated mold with a T-intersection. For the electrode layer, a stencil design is printed directly on the printing tray and covered with a piece of transparent glass. Microwire electrodes are adhered over the glass piece (guided by underlaying stencil) and a CAD design of the electrode layer is then printed on top of the microwire electrode. After delamination from the glass after printing, the microwire is embedded in the printed piece, with the stencil design ensuring that alignment and positioning of the electrode is reproducible for each print. After a thermal bonding step between the channel layer and electrode layer, a complete electrophoresis device with integrated microelectrodes for amperometric detection results. It is shown that this approach enables different microwire electrodes (gold or platinum) and sizes (100 or 50 µm) to be integrated in an end-channel configuration with no gap between the electrode and the separation channel. These devices were used to separate a mixture of catecholamines and the effect of separation voltage on the potential voltage applied on the working electrode was also investigated. In addition, the effect of electrode size on the number of theoretical plates and limit of detection was studied. Finally, a device that contains different channel heights and a detection electrode was 3D-printed to integrate continuous flow sampling with microchip electrophoresis and amperometric detection.

Schlagwörter

Stichwörter der Autor:innen

3D printingCapillary electrophoresis/electrophoresisElectroanalytical methods

Autor:innen und Institutionen

  • Department of Chemistry, Saint Louis University, Saint Louis, MO, USA.
  • Department of Chemistry, Saint Louis University, Saint Louis, MO, USA. scott.martin@slu.edu.
  • Center for Additive Manufacturing, Saint Louis University, Saint Louis, MO, USA. scott.martin@slu.edu.

Förderung

  • NIGMS NIH HHS
  • National Institute of General Medical Sciences

Zitieren

APA

Selemani, M. A., & Martin, R. S. (2024). Use of 3D printing to integrate microchip electrophoresis with amperometric detection. Analytical and Bioanalytical Chemistry, 416(21), 4749-4758. https://doi.org/10.1007/s00216-024-05260-6

Vancouver

Selemani MA, Martin RS. Use of 3D printing to integrate microchip electrophoresis with amperometric detection. Analytical and Bioanalytical Chemistry. 2024;416(21):4749-4758. doi:10.1007/s00216-024-05260-6

BibTeX
@article{Selemani2024,
  author = {Selemani, Major A and Martin, R Scott},
  title = {Use of 3D printing to integrate microchip electrophoresis with amperometric detection},
  journal = {Analytical and Bioanalytical Chemistry},
  year = {2024},
  volume = {416},
  number = {21},
  pages = {4749--4758},
  doi = {10.1007/s00216-024-05260-6}
}
Kostenlos starten →