EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Machining of WAAM-cladded Inconel 625 for energy components: influence of cutting conditions and tool geometry

Stepan Kolomy, Jan Zouhar, Martin Drbal, Radim Veselsky, Josef Sedlak, Petra Sliwkova

The International Journal of Advanced Manufacturing Technology · 2026-08 · 145 (7-8) · 4931-4941

DOI: 10.1007/s00170-026-18603-7 ↗

Kurz gefasst

Fachartikel in der Zeitschrift The International Journal of Advanced Manufacturing Technology, online erschienen am 02.07.2026. Verfasst von Stepan Kolomy und 5 weiteren Autor:innen. Die Arbeit wurde bisher 1-mal zitiert (Crossref) und nennt 24 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Brno University of Technology.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Effectivity and service life of energy components play very significant role in energy industry. Therefore, the Inconel cladding is applied to increase service life of metal tubes used in the incineration kettles. This study aims to examine the effect of cutting parameters and inserts geometry when turning of cladded Inconel 625 layer. The cladded Inconel 625 material was prepared by wire arc additive manufacturing method, which is employed as the effective cladding method of Inconel 625 on the metal tube. Testing was carried out by turning of spiral cladded Inconel 625 under different cutting conditions with different tool geometry. Cutting forces, surface roughness, tool life, chip formation and surface texture were investigated. The results showed that machining parameters have a significant effect on machinability, surface quality, and tool wear. The lower cutting conditions exhibited lower cutting forces and surface roughness compared to the tests carried out under the higher cutting conditions. The lower cutting speed resulted in lower tool wear monitored on the cutting inserts. At cutting speed of 15 m.min − 1 and feed 0.1 mm, the lamellar chip was formed with distinguishable shearing zones. The simulation of chip formation was performed using Finite element method analysis. The simulation revealed the lamellar chip formation when using the higher cutting speed. The result of the work can be effectively used when machining Inconel cladded material used in energy industry to ensure higher efficiency of whole components.

Förderung

  • Brno University of Technology

Zitieren

APA

Kolomy, S., Zouhar, J., Drbal, M., Veselsky, R., Sedlak, J., & Sliwkova, P. (2026). Machining of WAAM-cladded Inconel 625 for energy components: influence of cutting conditions and tool geometry. The International Journal of Advanced Manufacturing Technology, 145(7-8), 4931-4941. https://doi.org/10.1007/s00170-026-18603-7

Vancouver

Kolomy S, Zouhar J, Drbal M, Veselsky R, Sedlak J, Sliwkova P. Machining of WAAM-cladded Inconel 625 for energy components: influence of cutting conditions and tool geometry. The International Journal of Advanced Manufacturing Technology. 2026;145(7-8):4931-4941. doi:10.1007/s00170-026-18603-7

BibTeX
@article{Kolomy2026,
  author = {Kolomy, Stepan and Zouhar, Jan and Drbal, Martin and Veselsky, Radim and Sedlak, Josef and Sliwkova, Petra},
  title = {Machining of WAAM-cladded Inconel 625 for energy components: influence of cutting conditions and tool geometry},
  journal = {The International Journal of Advanced Manufacturing Technology},
  year = {2026},
  volume = {145},
  number = {7-8},
  pages = {4931--4941},
  doi = {10.1007/s00170-026-18603-7}
}
Kostenlos starten →