EUVIMEDEUVIMED entdecken
Crossref

Dynamic modeling of a standard internal tool holder

Wallyson Thomas Alves da Silva, Rouben Rostamian, Fabio Kuranaka, Marcus Vinicius Begossi, Alex Sandro Payão dos Santos, Anselmo Eduardo Diniz, Amauri Hassui, Jozef Peterka

The International Journal of Advanced Manufacturing Technology · 2026-07 · 145 (3-4) · 2965-2988

DOI: 10.1007/s00170-026-18516-5 ↗

Kurz gefasst

Fachartikel in der Zeitschrift The International Journal of Advanced Manufacturing Technology, online erschienen am 23.06.2026. Verfasst von Wallyson Thomas Alves da Silva und 7 weiteren Autor:innen. Die Arbeit nennt 44 Literaturangaben. Gefördert von: Conselho Nacional de Desenvolvimento Científico e Tecnológico, Vedecká Grantová Agentúra MŠVVaŠ SR a SAV, Kultúrna a Edukacná Grantová Agentúra MŠVVaŠ SR.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

The interface between a boring bar and its clamp housing has a major influence on the dynamic behaviour of internal turning tools. This paper presents and experimentally evaluates a compact multi-span Euler–Bernoulli model for a standard internal tool holder, in which the boring bar is represented by a free–pinned–pinned–free (F–P–P–F) beam. The model explicitly accounts for the two screw-contact stations and the remaining tail of the bar inside the holder, while keeping the formulation parameter-free and straightforward to implement. To address boundary-condition uncertainty, the proposed model is compared with a classical fixed–free cantilever approximation and with a free–spring–spring–free (F–S–S–F) elastic-support model based on screw-stiffness values reported in the literature. The experimental validation was performed for overhang ratios from \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$L/D=3$$\end{document} to \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$L/D=5$$\end{document}. The F–P–P–F model reduced the mean Natural Frequency Difference (NFD) to approximately \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$7.72\%$$\end{document}, compared with \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$31.50\%$$\end{document} for the fixed–free cantilever approximation and \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$12.00\%$$\end{document} for the elastic-support model. The results show that the proposed F–P–P–F formulation provides a practical balance between physical representativeness, low parameter dependence and computational simplicity. The remaining discrepancies are mainly attributed to clamp compliance, screw preload uncertainty, possible intermittent contact inside the holder and the idealization of the support conditions. The predicted natural frequencies are finally used as inputs for a theoretical stability-lobe analysis of the \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$L/D=5$$\end{document} case.

Förderung

  • Conselho Nacional de Desenvolvimento Científico e Tecnológico
  • Vedecká Grantová Agentúra MŠVVaŠ SR a SAV
  • Kultúrna a Edukacná Grantová Agentúra MŠVVaŠ SR

Zitieren

APA

Silva, W. T. A. D., Rostamian, R., Kuranaka, F., Begossi, M. V., Santos, A. S. P. D., Diniz, A. E., Hassui, A., & Peterka, J. (2026). Dynamic modeling of a standard internal tool holder. The International Journal of Advanced Manufacturing Technology, 145(3-4), 2965-2988. https://doi.org/10.1007/s00170-026-18516-5

Vancouver

Silva WTAD, Rostamian R, Kuranaka F, Begossi MV, Santos ASPD, Diniz AE, et al. Dynamic modeling of a standard internal tool holder. The International Journal of Advanced Manufacturing Technology. 2026;145(3-4):2965-2988. doi:10.1007/s00170-026-18516-5

BibTeX
@article{Silva2026,
  author = {Silva, Wallyson Thomas Alves da and Rostamian, Rouben and Kuranaka, Fabio and Begossi, Marcus Vinicius and Santos, Alex Sandro Payão dos and Diniz, Anselmo Eduardo and Hassui, Amauri and Peterka, Jozef},
  title = {Dynamic modeling of a standard internal tool holder},
  journal = {The International Journal of Advanced Manufacturing Technology},
  year = {2026},
  volume = {145},
  number = {3-4},
  pages = {2965--2988},
  doi = {10.1007/s00170-026-18516-5}
}
Kostenlos starten →