EUVIMEDEUVIMED entdecken
Crossref

A study on the effects of surface finishing methods on the internal surface roughness of 316L PBF-LB tubes

Foued Abroug, Maher Baili, Nagui Elgaby, Mohamad Rostom, Lionel Arnaud

The International Journal of Advanced Manufacturing Technology · 2026-07 · 145 (3-4) · 2117-2140

DOI: 10.1007/s00170-026-18404-y ↗

Kurz gefasst

Fachartikel in der Zeitschrift The International Journal of Advanced Manufacturing Technology, online erschienen am 12.06.2026. Verfasst von Foued Abroug und 4 weiteren Autor:innen. Die Arbeit nennt 28 Literaturangaben.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

This paper addresses the effects of different post-processing techniques on the internal surface roughness of 316 L stainless steel tubes, obtained via the Laser Powder Bed Fusion (PBF-LB) technique. The tubes have a cylindrical or triangular section and were manufactured horizontally to accentuate the as-built surface defects on the internal overhang surfaces. Mechanical, electrochemical and mechano-electrochemical-based post-processing techniques were applied to the tubes, according to industrial standards. The internal surfaces were scanned using a 3D profilometer and the Ra and Sa parameters were assessed. The results show that, despite the simple geometry of the tubes, obtaining low surface roughness is a difficult task, mainly due to accessibility issues. Only the micromachining process based on selective roughness processing achieves a very low surface roughness, below 2 μm. Mechanical and electrochemical processes allow for reducing surface roughness by almost half, and sometimes removed larger surface defects of the overhang surface, but they are generally limited techniques when facing internal geometries. A vibratory mass finishing technique also allows for reducing surface roughness by around 40%. Finally, one of the applied mechano-electrochemical finishing processes was not compatible with the tested geometries, due to the length/diameter ratio of the tube. This study contributes to a better understanding of the key factors that must be considered when comparing post-processing methods for additive manufacturing. It emphasizes that surface accessibility is a critical practical parameter, as many processes fail precisely because of this limitation. It also shows that traditional roughness parameters alone are not sufficient to characterize additively manufactured surfaces, since singular point- or line defects cannot be properly captured by such metrics.

Zitieren

APA

Abroug, F., Baili, M., Elgaby, N., Rostom, M., & Arnaud, L. (2026). A study on the effects of surface finishing methods on the internal surface roughness of 316L PBF-LB tubes. The International Journal of Advanced Manufacturing Technology, 145(3-4), 2117-2140. https://doi.org/10.1007/s00170-026-18404-y

Vancouver

Abroug F, Baili M, Elgaby N, Rostom M, Arnaud L. A study on the effects of surface finishing methods on the internal surface roughness of 316L PBF-LB tubes. The International Journal of Advanced Manufacturing Technology. 2026;145(3-4):2117-2140. doi:10.1007/s00170-026-18404-y

BibTeX
@article{Abroug2026,
  author = {Abroug, Foued and Baili, Maher and Elgaby, Nagui and Rostom, Mohamad and Arnaud, Lionel},
  title = {A study on the effects of surface finishing methods on the internal surface roughness of 316L PBF-LB tubes},
  journal = {The International Journal of Advanced Manufacturing Technology},
  year = {2026},
  volume = {145},
  number = {3-4},
  pages = {2117--2140},
  doi = {10.1007/s00170-026-18404-y}
}
Kostenlos starten →