Compressive behavior of PA6-CF lattice structures for rapid tooling: influence of infill pattern, infill density, and anisotropy
The International Journal of Advanced Manufacturing Technology · 2026-07 · 145 (1-2) · 745-769
DOI: 10.1007/s00170-026-18397-8 ↗Kurz gefasst
Fachartikel in der Zeitschrift The International Journal of Advanced Manufacturing Technology, online erschienen am 29.05.2026. Verfasst von Francesco Lambiase und 2 weiteren Autor:innen. Die Arbeit wurde bisher 1-mal zitiert (Crossref) und nennt 30 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Università degli Studi dell’Aquila.
Abstract (Originalsprache)
Fiber-reinforced thermoplastic lattice structures produced by fused deposition modeling (FDM) offer a promising route to lightweight, load-tailored components for rapid tooling, yet rational topology selection remains hindered by the lack of systematic structure-property data. This study addresses this gap by characterizing the compressive behavior of FDM-printed carbon-fiber-reinforced polyamide 6 (PA6-CF) lattice structures across three infill patterns (Cross Hatch, Gyroid, 3D Honeycomb), three relative densities (10%, 20%, 30%), three strain rates (6.6 × 10⁻³ to 4 × 10⁻¹ s⁻¹), and two loading orientations. Gibson-Ashby scaling analysis reveals that the dominant deformation mechanism — and therefore the design-relevant scaling law — depends critically on topology: Cross Hatch follows linear strength scaling ( n ≈ 1.0) governed by strut buckling, while Gyroid and 3D Honeycomb exhibit super-quadratic scaling ( n = 2.72 and 3.03, respectively), reflecting a buckling-to-yielding transition at higher densities that enables disproportionate strength gains. Mechanical anisotropy is topology-dependent: Cross Hatch suffers a 68% property reduction under transverse loading due to geometric directionality and unfavorable fiber alignment, whereas Gyroid maintains near-isotropic response (anisotropy indices 1.0–1.9) by distributing loads across multiple fiber orientations. Strain rate sensitivity is negligible for stretch-dominated Cross Hatch but increases strength by 10–25% for Gyroid and Honeycomb at higher densities, an advantage for impact applications. These findings establish topology- and density-specific design criteria that allow engineers to select PA6-CF lattice configurations based on loading mode, directionality, and energy absorption requirements, replacing empirical trial-and-error with quantitative performance predictions for rapid tooling applications.
Förderung
- Università degli Studi dell’Aquila
Zitieren
APA
Lambiase, F., Pace, F., & Andreucci, E. (2026). Compressive behavior of PA6-CF lattice structures for rapid tooling: influence of infill pattern, infill density, and anisotropy. The International Journal of Advanced Manufacturing Technology, 145(1-2), 745-769. https://doi.org/10.1007/s00170-026-18397-8
Vancouver
Lambiase F, Pace F, Andreucci E. Compressive behavior of PA6-CF lattice structures for rapid tooling: influence of infill pattern, infill density, and anisotropy. The International Journal of Advanced Manufacturing Technology. 2026;145(1-2):745-769. doi:10.1007/s00170-026-18397-8
BibTeX
@article{Lambiase2026,
author = {Lambiase, Francesco and Pace, Francesco and Andreucci, Elena},
title = {Compressive behavior of PA6-CF lattice structures for rapid tooling: influence of infill pattern, infill density, and anisotropy},
journal = {The International Journal of Advanced Manufacturing Technology},
year = {2026},
volume = {145},
number = {1-2},
pages = {745--769},
doi = {10.1007/s00170-026-18397-8}
}
EUVIMED